manualshive.com logo in svg

Cisco 7401ASR, Installation And Configuration Manual

Share
Download
Cisco 7401ASR Installation And Configuration Manual Download Page 29

1-9

Cisco 7401ASR Installation and Configuration Guide

OL-5419-01 B0

Chapter 1      Overview and Parts Installation

  Installing the CompactFlash Disk, GBIC, and Port Adapter

Warning

Class 1 LED product.

Figure 1-6

Inserting a GBIC into the Cisco 7401ASR Gigabit Ethernet Slot 0

Use the following procedure to install a GBIC:

Step 1

Attach an ESD-preventive wrist strap between you and an unpainted chassis surface.

Step 2

Locate the label on the GBIC and turn the GBIC so the label is on top and the alignment groove is 
down.

Note

The GBIC is keyed so that it cannot be inserted incorrectly.

Step 3

Insert the GBIC into GBIC slot 0 or 1. The tabs on either side of the GBIC snap into place when you 
have completely and properly inserted the GBIC.

Step 4

Repeat Step 2 and Step 3 if you are inserting a second GBIC.

Note

Do not remove the plug from the GBIC optical bores until you are ready to install the network interface 
optical fiber cable. Save the plug for future use.

This completes the GBIC installation procedure. 

1

Gigabit Interface Converter (GBIC)

4

GBIC port 1

2

Alignment groove

5

Plug

3

GBIC port 0

57603

1

3

5

2

4

Summary of Contents for 7401ASR




























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands