manualshive.com logo in svg

Cisco 7401ASR, Installation And Configuration Manual

Share
Download
Cisco 7401ASR Installation And Configuration Manual Download Page 10

x

Cisco 7401ASR Installation and Configuration Guide

OL-5419-01 B0

Preface

Organization

Organization

The major sections of this guide are as follows:

Document Conventions 

Command descriptions use the following conventions:

Screen examples use the following conventions:

Chapter

Title

Description

1

Overview and Parts Installation

This chapter provides a hardware overview as well as preparation and 
installation instructions for a Gigabit Interface Converter (GBIC), 
CompactFlash Disk, and port adapter or service adapter.

2

Rack-Mounting, Tabletop 
Installation, and Cabling

This chapter provides preparation and installation instructions for 
installing the chassis in a rack and for attaching cables.

3

Starting and Configuring

This chapter provides a functional overview of the system, as well as 
startup and configuration instructions.

4

Configuring the VPN Acceleration 
Module

This chapter provides configuration instructions for the VPN 
Acceleration Module (VAM).

5

Troubleshooting

This chapter provides basic system startup troubleshooting information.

A

Specifications

This appendix provides system specifications as well as port and cabling 
pinouts and specifications.

B

PXF Information

This appendix contains information about enabling PXF features, and 
PXF show commands.

C

Using the CompactFlash Disk

This appendix contains information about using the CompactFlash Disk.

D

Configuration Register Information

This appendix contains configuration register information.

boldface font

Commands and keywords are in boldface.

italic font

Arguments for which you supply values are in italics.

[ ]

Elements in square brackets are optional.

{ x | y | z }

Alternative keywords are grouped in braces and separated by vertical bars.

[ x | y | z ]

Optional alternative keywords are grouped in brackets and separated by 
vertical bars.

string

A nonquoted set of characters. Do not use quotation marks around the string, 
or the string will include the quotation marks.

screen

 font

Terminal sessions and information the system displays are in 

screen

 font.

boldface screen

 font

Information you must enter is in 

boldface screen

 font.

italic screen font

Arguments for which you supply values are in italic screen font.

Summary of Contents for 7401ASR




























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands