manualshive.com logo in svg

Cisco 4000 Series, Hardware Installation Manual, Page: 65 / 206

Share
Download
Cisco 4000 Series Hardware Installation Manual Download Page 65

 

2-11

Hardware Installation Guide for the Cisco 4000 Series  Integrated Services Router

OL-32185-02

Chapter 2      Cisco 4000 Series ISRs Preinstallation

  Network Cabling Specifications

Console and Auxiliary Port Considerations

The router includes an asynchronous serial console port and an auxiliary port. You access to the router 
either locally using a console terminal connected to the console port, or remotely using a modem 
connected to the auxiliary port. This section discusses important cabling information you must consider 
before connecting the router to a console terminal or modem.

The major difference between the console and auxiliary ports is that the auxiliary port supports hardware 
flow control and the console port does not. Flow control paces the transmission of data between a 
sending and a receiving device. Flow control ensures that the receiving device can absorb the data sent 
to it before the sending device sends more data. When the buffers on the receiving device are full, a 
message is sent to the sending device to suspend transmission until the data in the buffers is processed. 
Because the auxiliary port supports flow control, it is suited for use with the high-speed transmissions 
of a modem. Console terminals send data at speeds slower than the speeds modems do; therefore, the 
console port is ideally suited for use with console terminals.

Note

Cisco 4221 ISR does not have an auxiliary port.

Console Port Connections

The router has both EIA/TIA-232 asynchronous (RJ-45) and USB 5-pin mini Type B, 2.0 compliant 
serial console ports. Shielded USB cables with properly terminated shields are recommended.

EIA/TIA-232

Depending on the cable and the adapter used, this port appears as a DTE or DCE device at the end of the 
cable. At a time, only one port can be used.

The default parameters for the console port are 9600 baud, 8 data bits, 1 stop bit, and no parity. The 
console port does not support hardware flow control. For detailed information about installing a console 
terminal, see the 

“Connect to Console Terminal or Modem” section on page 3-22

. 

For cable and port pinouts, see the 

Cisco Modular Access Router Cable Specifications

 

document.

USB Serial Console

The USB serial console port connects directly to the USB connector of a PC using a USB Type A to 5-pin 
mini USB Type-B cable. The USB Console supports full speed (12Mb/s) operation. The console port 
does not support hardware flow control.

Note

Cisco 4461 supports Mini-USB Type B serial port and Micro-USB Type B serial port

Note

Always use shielded USB cables with a properly terminated shield.

The default parameters for the console port are 9600 baud, 8 data bits, no parity, and 1 stop bit. For 
detailed information about installing a console terminal, see the 

“Connect to Console Terminal or 

Modem” section on page 3-22

.

Summary of Contents for 4000 Series















































































































































































































Reviews:

No comments