manualshive.com logo in svg

Cisco 3750 - Catalyst EMI Switch, Hardware Installation Manual

Share
Download
Cisco 3750 - Catalyst EMI Switch Hardware Installation Manual Download Page 120

 

Chapter 3      Switch Installation

Installing and Removing SFP Modules

3-42

Catalyst 3750 Switch Hardware Installation Guide

78-15136-03

For detailed instructions on installing, removing, and cabling the SFP module, 
refer to your SFP module documentation.

Installing SFP Modules into SFP Module Slots

Figure 3-37

 shows an SFP module that has a bale-clasp latch. 

Caution

We strongly recommend that you do not install or remove fiber-optic SFP modules 
with cables attached because of the potential damage to the cables, the cable 
connector, or the optical interfaces in the SFP module. Disconnect all cables 
before removing or installing an SFP module.

Removing and installing an SFP module can shorten its useful life. Do not remove 
and insert SFP modules more often than is absolutely necessary.

Figure 3-37 SFP Module with a Bale-Clasp Latch

To insert an SFP module into the SFP module slot, follow these steps:

Step 1

Attach an ESD-preventive wrist strap to your wrist and to a bare metal surface on 
the chassis.

Step 2

Find the send (TX) and receive (RX) markings that identify the top side of the SFP 
module.

86575

Summary of Contents for 3750 - Catalyst EMI Switch







































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands