background image

VCC-SXCXP3R                                                                   Rev. 905-0050-00 

 

©2017 CIS Corporation. All rights reserved. 

1.

 

Handling Precautions 

 

The camera module must not be used for any nuclear equipment  or aerospace equipment  with which 

mechanical failure or malfunction could result in serious bodily injury or loss of human life.  Our warranty 

does not apply to damages or defects caused by irregular and/or abnormal use of the product. 

All specifications contained herein are subject to change without prior notice.    Reproduction in whole or in 

part is prohibited. 

 

Please observe all warnings and cautions stated below.     

Our warranty does not apply to damages or malfunctions caused by neglecting these precautions. 

 

 

Do not use

 

or store

 

the camera module in the dusty or humid places. 

 

Do not apply excessive force, vibration, or static electricity that could damage the camera.  Handle the camera 
with care.   

 

Do not shoot direct images that are extremely bright (e.g., light source, sun, etc).    When extremely strong light 
source is shot, smear or blooming may occur.

  

When the camera is not in use, please put the protection cap on. 

 

Follow the instructions in Chapter 5, “External Connector Pin Assignment” for connecting the camera module.   

Improper connection may cause damages not only to the camera module but also to the connected devices. 

 

Confirm the mutual ground potential carefully and then connect the camera module to monitors or 

computers.    AC leaks from the connected devices may cause damages or destroy the camera module. 

 

Do not apply excessive voltage. (Use only the specified voltage.)    Unstable or improper power supply 

voltage may cause damages or malfunction of the camera assembly. 

 

Do not disassemble the camera.    The camera once disassembled shall be out of warranty. 

 
2.

 

Product Outline 

 

VCC-SXCXP3R is a CoaXPress interfaced small color camera utilizing a 1/2 type, 1.3M pixels CMOS image sensor. 
 

Features 

 

29mm x 29mm x 29mm cubic in size 

 

Global shutter CMOS (Color) 

 

CoaXPress CXP-1, CXP-2, and CXP-3 x 1 for each. 

 

High speed frame rate: 168fps (at CXP-3 ROI OFF). 

 

The maximum cable length: Approx. 100m (at CXP-1). 

 

ROI 

 

Sub-sampling 

 

Exposure, Gain settings 

 

External trigger mode (Fixed trigger shutter mode / Pulse width trigger shutter mode) 

 

Sequence control function 

 

Shading correction 

 

GenICam complied 

 

3.

 

Bundled Items 

3.1.

 

Standard Bundled Items 

 

Camera module, VCC-SXCXP3R 

 

Lens cap 

 
3.2.

 

Packaging 

 

Individual carton 

 

Master carton (10pcs/carton) 

Note) Q’ty per master carton may vary depends on the shipping q’ty. 

 

 

Summary of Contents for VCC-SXCXP3R

































Reviews: