background image

  VCC-5CXP3R   

 

Rev. 905-0052-00 

©2016 CIS Corporation. All rights reserved. 

 

7.3.1    Internal Sync Mode (Free Run Mode) 

 

This is a mode to use triggers continuously made in the camera. No external trigger shall be used. 

 

Please set TriggerSelectorAndActvation to AcquisitionMode. 

 

Configuration 

Frame rate

 

(fps) 

8bit 

10bit 

CXP-1 

21.3 

16.3 

CXP-2 

42.6 

34.8 

CXP-3 

42.6 

42.6 

CXP-5 

85.1 

69.5 

CXP-6 

85.1 

85.1 

 

7.3.2    External Trigger Sync Mode 

This is a mode to input external trigger signals to capture images by any preferred timings. 
Some delay shall be considered from when camera recognized the trigger edge to when actual exposure starts.     
Please refer to the delay time as below.

 

 

 

 

Input 

Delay Time 

LinkTrigger0 

Approx. 3.4us   

Line0 

Approx. 150us 

 

Notes for trigger pulse input timing

 

 

A trigger pulse can be input during Readout. However, please do not input a trigger pulse while reading out signals for the prior 
frame since it ends its exposure. (In other words, please avoid inputting a trigger pulse while reading out signals for the prior 
frame and starts reading out signals for the next frame.)   
 

 

 

Video output from the camera might not be executed when the trigger is input again at the prohibited timing, or right after 
FVAL turns to “L” at the timing of the end of exposure. If the camera stops operating, or cannot output image data without 
malfunctions, please execute “SensorReset” command after quitting trigger input to start the operation again. 
 

If the camera does not start its operation, please execute the restoration of power. 

 

 

Device Control

 

SensorReset

 

(Execute)

 

Trigger 

Exposure 

FVAL 
(

Readout) 

Aegis Electronic Group, Inc.

Summary of Contents for VCC-5CXP3R

































Reviews: