manualshive.com logo in svg

Cirrus Logic CDB48500-USB, Manual, Page: 8 / 52

Share
Download
Cirrus Logic CDB48500-USB Manual Download Page 8

Introducing the CDB48500-USB Customer Development Kit

CDB48500--USB Evaluation Kit Guide

DS784DB1

©

Copyright 2008 Cirrus Logic , Inc.

1-2

host PC to the CDB48500 board, and convert GUI commands into the serial control protocol required for 
configuring the CS485XX DSP, (2)CS42448 codecs, and CS8416 S/PDIF receiver ICs. 

Figure 1-1

 shows 

the relationship between the PC, CS485XX, and the CDB USB MASTER

 Figure 1-1. CDB48500-USB System Block Diagram

This document will concentrate on the features and basic operation of the CDB48500-USB board. 
Detailed information regarding the operation and programming of the CS485XX DSP is covered by the 
CS485XX data sheet, CS485XX Hardware User’s Manual, and application note AN298 (see 

Section 

1.2.2,  “Related Documentation”  on page 1-4

 for more details).

The CDB48500-USB is a convenient and easy-to-operate evaluation platform. It has been designed to 
demonstrate the majority of the CS485XX functions on a small 6" x 6.5" base board. These features 
include:

•

PC control of the CS485XX using the DSP Composer™ graphical user interface

•

Serial control of audio devices on CDB48500 via I

2

C

®

 or SPI™ protocols

•

Digital audio input of PCM via optical or coaxial S/PDIF (does not support compressed data input)

•

Up to 12-channel analog audio input via the two CS42448 audio codecs

•

Up to 12-channel analog output through the two CS42448 audio codecs

•

Digital audio output of PCM data via optical S/PDIF

•

Headphone output jack 

•

Multi-channel digital audio input via the CDB USB MASTER card (not yet supported)

•

Separate input and output clocking domains to allow 1FS-to-2FS audio processing on the CS485XX

•

Fast boot – host-controlled master boot (HCMB) of custom applications from 4 Mbit serial SPI flash 
device.

•

Microphone input with integrated amplifier for Intelligent Room Calibration (IRC) evaluation (future)

•

Supports all members of the CS485XX family in the 48-pin LQFP package.

Note:  Not all features of the CS485xx are exercised on the CDB48500.

 1.2.1 Identifying CDB48500-USB Components

Figure 1-2

 shows the top side of the CDB48500-USB Evaluation Board. The accompanying legend 

identifies the main components of the board.

CDB48500

Reset Signals

USB Port

Serial Control Interface

Board Control Signals

Audio Data (Future Development)

PC

CD

B USB

 MA

STER

Summary of Contents for CDB48500-USB





















































Reviews:

No comments