manualshive.com logo in svg

Cirrus Logic CDB48500-USB, Manual, Page: 14 / 52

Share
Download
Cirrus Logic CDB48500-USB Manual Download Page 14

Introduction

CDB48500-USB Evaluation Kit Guide

DS784DB1

©

Copyright 2008 Cirrus Logic, Inc.

2-4

B. Use the RCA audio cables to connect these line-level analog outputs to powered speakers.

 2.1.3 Connecting to a PC

Follow these steps to connect to a PC:

1.

Connect the “B” end of the USB cable to P1 on the CDB USB MASTER USB Digital I/O Card.

2. Connect the “A” end of the USB Cable to a USB 2.0 port on a notebook or PC running Win XP.

3. Windows should recognize that a new device has been attached and display a notice saying “Found 

New Hardware”. 

 Figure 2-3. Found New Hardware Service Window

4. Windows will display the Found New Hardware Wizard (below). Select the No, not at this time radio 

button so that Windows does not connect to Windows Update for the drivers. Click Next.

 Figure 2-4. Found New Hardware Wizard Welcome Window

5. Windows will then ask whether to use automatic installation or manual installation. Allow Windows to 

install the software automatically and click Next.

Summary of Contents for CDB48500-USB





















































Reviews:

No comments