manualshive.com logo in svg

Cincinnati KS-70, Manual

Share
Download
Cincinnati KS-70 Manual Download Page 20

4600 N. Mason Montgomery Road  

·

  

Mason, OH 45040

 

800

-

677

-

0076  

·

  Fax: 513

-

923

-

5694

www.CinInd.com  

·

  [email protected]

 

A Subsidiary of The Armor Group, Inc.

 

Version 1.04

 

October 2014

 

PROBLEM

 

DIAGNOSIS

 

Will not shut off. 

Faulty programmable relay.

 

Dirty rinse valve (piston sticking open).

 

Will not turn on. 

Faulty programmable relay.

 

Dirty rinse valve (piston sticking closed).

 

Faulty valve coil.

 

Excessive water vapor.

 

Water temperature too high.

 

Water pressure/flow too high.

 

Rinse temperature too low. 

Inlet water temperature too low—does not match design conditions.

 

Gas/Electric booster—temperature controller improperly adjusted.

 

Steam Booster—low steam pressure.

 

Steam Booster—clogged strainer.

 

Steam Booster—back pressure in condensate line.

 

Steam Booster—faulty steam trap.

 

Rinse

 

Exhaust Fan / Motor

 

PROBLEM

 

DIAGNOSIS

 

Fan/motor vibration.  

Worn bearings.

 

Wheel out of balance.

 

Bent shaft.

 

Low voltage.

 

Motor overheating. 

Bent shaft.

 

Worn bearing.

 

Running backwards.

 

Page 16 

KS-70 R

ACK

 W

ASHER

 

T

ROUBLESHOOTING

 G

UIDE

 

Summary of Contents for KS-70























Reviews:

No comments

Brands by name

Popular brands

Load more brands