CIAT DESTRATIFIER TPL 4000, Instruction Manual

Page: 15 / 24

14 - CONTROL UNITS
Eco+ 1-PH BOX (for Heliotherme or destratifier units fitted with 1-PHASE motors)
Thank you for purchasing the electronic regulation solution "Eco+ 1-PH BOX" for HELIOTHERME or
DESTRATIFIER units fitted with 1-PHASE motors. Up to 3 HELIOTHERME or 3 DESTRATIFIER units can
be controlled using a single box.
This box allows the following:
• Proportional variation of the supply air speed of the ROTOREX 1-phase fan motor assembly (FMA)
according to the heating requirements of your building.

Heat or cool as precisely as possible in accordance with your needs.
• The heat exchanger is proportionally supplied with water according to the heating requirements of your
building (available with valve kit option).

The supply air temperature will be controlled thereby increasing your comfort level.
• The internal timer can be configured on a weekly basis using 3 operating modes (Comfort, Eco, Frost protection), allowing
you to use your air heaters economically and responsibly.

The heat gain achieved by your building will depend on its occupancy level.
Refer to the instruction manual supplied in the packaging of your Eco+ 1-PH BOX for further information
or contact your CIAT
agent
Eco+ 3-PH BOX (for Heliotherme or destratifier units fitted with 3-PHASE motors)
Thank you for choosing the "PLUG & PLAY" (the electrical components are selected and wired, facilitating
installation) control solution with built-in Eco+ 3-PHASE BOX electronics for HELIOTHERME or DESTRATIFIER
units equipped with 3-phase motors.
This box allows the following:
• Automatic or manual selection of two supply air velocities for the three-phase ROTOREX fan motor assembly
(FMA), based on the heating demand for your building.

Heat or cool as precisely as possible in accordance with your needs.
• Supply water to one or more heat exchangers in proportion to your building's heat requirements (available
with the optional valve kit or on the circulator).

Control your supply air temperature to improve comfort levels and maintain the range of the air
streams.
• Choose between fresh air only or mix with frost protection via the actuator to be installed on the 2-channel
mixing box with built-in filter (available with the fresh air kit damper ac frost protection thermostat
kit) or 100% recirculated air.

Adjust the fresh air rates in your building to meet prevailing requirements or based on room occupancy levels
(built-in timer).
• Make wise use of your air heaters with the built-in programmable weekly timer with five operating modes (Off, Fresh Air
Comfort, Return Air Comfort, Eco and Frost Protection).

The heating and fresh air requirements for your building will depend on its occupancy level.
• Centralised management of the HELIOTHERME or DESTRATIFIER units via the master controller allowing 3 Eco+ 3-PHASE
BOX slave units to be controlled (one Eco+ 3-PHASE BOX slave unit controls a single HELIOTHERME or DESTRATIFIER
unit).

You can view the operating status of your HELIOTHERME or DESTRATIFIER unit individually (fresh air or return
air, motor fault, risk of frost etc.)
Refer to the instruction manual supplied in the packaging of your Eco+ 3-PH BOX box for further information or contact your CIAT
agent.
Eco+ ELEC BOX (for HELIOTHERMES equipped with electric heaters and 3-phase motors)
Thank you for choosing the "PLUG & PLAY" (the electrical components are selected and wired, facilitating
installation) control solution with built-in Eco+ ELEC BOX electronics for HELIOTHERME units equipped with
electric heaters and 3-phase motors. This box allows the following:
• Selection and combination of the electric heater power stages in various combinations based on heating
demands of your building.

Precision heating to meet your every need.
• Post-ventilation of the electric heater when the building no longer requires heating.

This protects your installation and your building from any potential fire hazards, in compliance
with articles CH34/37 and EN 60204-1 relating to fire hazards.
• Make wise use of your air heaters with the built-in programmable weekly timer with four operating modes
(Off, Comfort, Eco and Frost Protection).

The electrical requirements of your building will depend on its occupancy level.
• Centralised management of the HELIOTHERMES via the master controller allowing 3 Eco+ ELEC BOX
slave units to be controlled (one Eco+ ELEC BOX slave unit controls a single HELIOTHERME).

You can view the operating status of your HELIOTHERME individually (current operating mode, coil fault, motor
fault…)
Refer to operating manual no. 09.36 supplied in the packaging of your ELEC Eco+ BOX for further information or contact your
CIAT agent .
EN-15 H4000 HELIOTHERME