manualshive.com logo in svg

CIAT CIATControl OPC Server, Installation And Operating Instructions Manual

Share
Download
CIAT CIATControl OPC Server Installation And Operating Instructions Manual Download Page 16

 

 

 

NA 12.46 A

 

©2012

 

CIAT

 

NA 12.46 A 

installation instructions 

[16]

 

V05.2012

 

 

P53  

Output synchronisation  

0 = Inactive  
1 = on input D1  

2 = on input D2  
3 = on comfort mode  
4 = on input D1 and comfort  
5 = on input D2 and comfort  

6 = with KNX OnOff signal  
7 = with KNX OnOff signal and comfort  

0:1:2:3:4:5  

Do not change/ 

Manufacturer only 

P54  

Control of synchronised 

output  

Selection of output used for the fresh air damper, or of the 
synchronised output:  

1 = 24V valve output  
2 = 230V elec output  

01:02 

Do not change/ 

Manufacturer only 

P55  

Heating electrical power 
(based on 230 V)  

If an electric heater is used, the power (in kW) must be 
indicated in this parameter, rounded up to the nearest 100W. 
Used for certain energy consuming applications  

0…20.0 resolution of 0.1  

Read/Write 

P56  

LS power  

The power must be indicated, rounded to the nearest 5 or 10 

kW, in this parameter. Used for certain energy consuming 
applications  

5…990; resolution of 5  

Read/Write 

P57  

MS power  

The power must be indicated, rounded to the nearest 5 or 10 
kW, in this parameter. Used for certain energy consuming 

applications  

5…990; resolution of 5  

Read/Write 

P58  

HS power  

The power must be indicated, rounded to the nearest 5 or 10 
kW, in this parameter. Used for certain energy consuming 
applications  

5…990; resolution of 5  

Read/Write 

P59  

Hot water coil nominal 
capacity  

Nominal capacity (in kW) of the hot water coil, rounded up to 
the nearest 100 W. Used for certain energy consuming 

applications  

0…99.0 resolution of 0.1  

Read/Write 

P60  

Cold water coil nominal 

capacity  

Nominal capacity (in kW) of the cold water coil, rounded up to 
the nearest 100W. Used for certain energy consuming 
applications  

0…99.0 resolution of 0.1  

Read/Write 

P61  

Duration of electric heater 
cycle output Q14  

Duration of time-proportional signal cycle for continuous control 

0 = On/off operation  
30…300 = cycle time in seconds  

30…300; resolution of 30 s  

Do not change/ 

Manufacturer only 

P62  

Base outdoor temperature   Lowest outdoor temperature for electric heater power limiting  

-35…+5  

Read/Write 

P63  

Excess capacity difference   Temperature difference (°C) between the real energy limitation 

curve and the theoretical energy limitation curve  

0…5; resolution of 0.5  

Do not change/ 

Manufacturer only 

P64  

Setpoint drift as a function 

of the outdoor 
temperature Control slope  

Max difference between cold setpoint and outdoor temperature  
0 = Inactive  

0…20  

Read/Write 

P65  

Setpoint drift as a function 
of the outdoor 

temperature Max. setpoint  

There is no longer any setpoint drift beyond a certain outdoor 
temperature  

25…40  

Do not change/ 

Manufacturer only 

P66  

Free cooling  

For the fresh air function: minimum difference (°C) between the 
indoor and outdoor temperatures in order to automatically shift 
to free cooling mode  

0…10  

Do not change/ 

Manufacturer only 

P67  

Battery/coil use 
authorisation  

1 = hyd electric  
2 = hydraulic only  

3 = electric only  

01:02:03 Read/Write 

P68  

Fan coil unit valve motor 
type  

1 = 3 points  
2 = On/off  
3 = Thermal  

4 = 0/10 V  

01:02:03 

Do not change/ 

Manufacturer only 

P69  

Valve type (NC or NO) for 
thermal actuator  

1 = Normally closed  
2 = Normally open  

01:02 

Do not change/ 

Manufacturer only 

P70  

Stroke time of 3-position 
actuator  

Actuator stroke time, in seconds  

0…230; resolution of 5  

Do not change/ 

Manufacturer only 

P71  

Thermo valve  

Preheating time for valve before time-proportional algo 
Necessary to create this parameter to be confirmed by tests in 

the CIAT lab  

- 

Do not change/ 

Manufacturer only 

P72  

Thermo valve  

Heating percentage at 10% of demand  

0…100  

Do not change/ 

Manufacturer only 

P73  

Thermo valve  

Heating percentage at 100% of demand  

0…100  

Do not change/ 

Manufacturer only 

P74  

Thermo valve  

Valve opening time base, in seconds  

5…300; resolution of 5  

Do not change/ 

Manufacturer only 

P75  

Changeover measurement  

Duration, in minutes, of the test cycle to determine the 

changeover state (heating, cooling, or neither heating nor 
cooling)  

0…10  

Do not change/ 

Manufacturer only 

 
 

Summary of Contents for CIATControl OPC Server

































Reviews:

No comments

Brands by name

Popular brands

Load more brands