Chrysler Pacifica Hybrid 2020 Owner'S Manual Download Page 53 | Manualshive

Page: 53 / 108

Chrysler Pacifica Hybrid 2020 Owner'S Manual Download Page 53

51

(Continued)

to secure a child restraint system. For addi

-

tional  information, refer to “Installing Child
Restraints  Using  The  Vehicle  Seat  Belt”
under  the  “Child  Restraints”  section  of  the
Owner’s Manual. The figure below illustrates
the locking feature for each seating position.

7 Passenger Quad Seat Automatic Locking Re-

tractor (ALR) Locations

If the passenger seating position is equipped
with an ALR and is being used for normal
usage, only pull the seat belt webbing out far
enough to comfortably wrap around the occu

-

pant’s mid-section so as to not activate the
ALR. If the ALR is activated, you will hear a
clicking sound as the seat belt retracts. Allow

the webbing to retract completely in this case
and then carefully pull out only the amount of
webbing necessary to comfortably wrap
around the occupant’s mid-section. Slide the
latch plate into the buckle until you hear a
"click."

In  Automatic  Locking  Mode,  the  shoulder
belt  is  automatically  pre-locked.  The  seat
belt  will  still retract  to  remove  any  slack  in
the shoulder belt. Use the Automatic Locking
Mode anytime a child restraint is installed in
a  seating  position  that  has  a  seat  belt  with
this feature. Children 12 years old and under
should  always  be  properly  restrained  in  the
rear seat of a vehicle with a rear seat.

How To Engage The Automatic Locking Mode

1. Buckle the combination lap and shoulder

belt.

2. Grasp the shoulder portion and pull

downward until the entire seat belt is
extracted.

3. Allow the seat belt to retract. As the seat

belt retracts, you will hear a clicking
sound. This indicates the seat belt is now
in the Automatic Locking Mode.

How To Disengage The Automatic Locking Mode

Unbuckle the combination lap/shoulder belt
and allow it to retract completely to disen

-

gage the Automatic Locking Mode and acti

-

vate the vehicle sensitive (emergency)
locking mode.

ALR — Switchable Automatic Locking Re

-

tractor

WARNING!



Never place a rear-facing child restraint
in  front  of  an  air  bag.  A  deploying
passenger front air bag can cause death
or  serious  injury  to  a  child  12  years  or
younger,  including  a  child  in  a
rear-facing child restraint.



Never install a rear-facing child restraint
in the front seat of a vehicle. Only use a
rear-facing child restraint in the rear
seat. If the vehicle does not have a rear
seat, do not transport a rear-facing child
restraint in that vehicle.

WARNING! (Continued)

2020_CHRYSLER_PACIFICA_HYBRID_SUPP_USA=GUID-876DAAE8-C65F-4BC7-BAA9-813BB1426F1D=1=en=.book Page 51

«
...
51
52
53
54
55
...
»

Summary of Contents for Pacifica Hybrid 2020













































































































Reviews:

No comments