manualshive.com logo in svg

Chrysler Pacifica Hybrid 2020, Owner'S Manual, Page: 44 / 108

Share
Download
Chrysler Pacifica Hybrid 2020 Owner'S Manual Download Page 44

42

 — Liftgate Open Warning Light  

This  warning  light  will  illuminate  when  the
liftgate is open.

NOTE:

If the vehicle is moving, there will also be a
single chime.

 — Hybrid Electric Vehicle System Service 

Light

This  warning  light  will  illuminate  when
service  to  the  hybrid  electric  system  is
needed. It will be accompanied by a "Service
Hybrid Electric  Vehicle System" message in
the  cluster.  If  the  telltale  stays  on  or
continues to come on, contact an authorized
dealer as soon as possible.

 — Plug Status Fault Warning Light

This warning light will illuminate when a plug
status fault is detected (when vehicle not in
motion). It will be accompanied by a cluster
message indicating the type of fault. You may
receive  one  of  the  following  messages  if  a
fault is detected:

“Service  Charging  System”  –  If  you  see
this message, it is recommended to unplug

and  plug  in  again,  or  try  a  different
charging  station.  If  an  issue  continues,
contact  your  authorized  dealer  to  service
your high voltage charging system.

“Issue Detected  Check  External  Charging
Station”  –  If  you  see  this  message,  the
charging  station  maybe  powered  off,
having internal fault or being scheduled to
charge  later.  It  is  recommended  to  try  a
different  charging  station.  If  an  issue
continues,  then  contact  your  authorized
dealer.

NOTE:

Older  or  non-compliant  J1772  EVSE
models  may  not  support  charging  of  this
vehicle. If this vehicle does not charge, it
may  be  connected  to  a  non-compliant
Level  2  EVSE,  and  will  flash  indicators.
Please identify this failure to the site oper

-

ator and/or EVSE provider.

Before  this  vehicle  can  be  driven,  the
EVSE Charging Cord must be disconnected
from the vehicle.

 — Torque Limited Warning Light

This  warning  light  illuminates  when  vehicle
acceleration is limited due to a reduction in
engine  or  electric  motor  performance.
Contact your authorized dealer for service if
illumination persists.

Yellow Warning Lights

 — Anti-Lock Brake (ABS) Warning Light 

This  warning  light  monitors  the  Anti-Lock
Brake  System  (ABS).  The  light  will  turn  on
when the ignition is placed in the ON/RUN or
ACC/ON/RUN position and may stay on for as
long as four seconds.

If the ABS light remains on or turns on while
driving,  then  the  Anti-Lock  portion  of  the
brake system is not functioning and service is
required  as  soon  as  possible.  However,  the
conventional  brake  system  will  continue  to
operate  normally,  assuming  the  Brake
Warning Light is not also on.

If  the  ABS  light does  not turn  on when  the
ignition is placed in the ON/RUN or ACC/ON/
RUN  position,  have  the  brake  system
inspected by an authorized dealer.

2020_CHRYSLER_PACIFICA_HYBRID_SUPP_USA=GUID-876DAAE8-C65F-4BC7-BAA9-813BB1426F1D=1=en=.book  Page 42  

Summary of Contents for Pacifica Hybrid 2020













































































































Reviews:

No comments