manualshive.com logo in svg

Chrysler Pacifica Hybrid 2020, Owner'S Manual, Page: 35 / 108

Share
Download
Chrysler Pacifica Hybrid 2020 Owner'S Manual Download Page 35

33

Vehicle Info

Push and release the 

up

 or 

down

 arrow button

until Vehicle Info is highlighted in the instru

-

ment  cluster  display.  Push  the 

left

  or 

right

arrow  button to  scroll  through  the  following
information submenus:

Tire Pressure

If tire pressure is 

OK

 for all tires, a vehicle 

ICON is displayed with tire pressure values 
in each corner of the ICON.

If one or more tires have low pressure, “In

-

flate Tire To XX” is displayed with the ve

-

hicle ICON, and the tire pressure values in 
each corner of the ICON with the pressure 
value of the low tire displayed in a different 
color than the other tire pressure value.

If the Tire Pressure system requires ser

-

vice, “Service Tire Pressure System” is 
displayed.

Tire Pressure is an information only func

-

tion and cannot be reset.

Refer to “Tire Pressure Monitoring System 
(TPMS)” under “Safety” for further infor

-

mation.

Coolant Temperature

 

Displays the actual coolant temperature.

Oil Temperature

 

Displays the actual oil temperature.

Oil Pressure

 

Displays the actual oil pressure.

Battery Voltage

 

Displays the actual battery voltage.

Engine Hours — If Equipped

 

Displays the number of hours of engine op

-

eration.

Oil Life

 

Displays the remaining engine oil life as a 

percentage.

To reset the Oil Life, you must hold the OK 

button. The “Hold OK to Reset” instruc

-

tion will be displayed at all times, but the 

following conditions will need to be met in 

order to reset Oil Life:

The  vehicle  propulsion  system  must  be

OFF

The  ignition  must  be  in  the  ON/RUN

position

If the conditions are met, holding the 

OK

 

button will reset the gauge and the numer

-

ic display will return to 100%.

If the conditions are not met, a popup 

message will display for five seconds, de

-

scribing the required conditions, and then 

the Oil Life screen will reappear.

NOTE:

This  procedure  should  only  be  performed

after  scheduled  maintenance  is  completed.

Resetting oil life other than when associated

with a scheduled maintenance may result in

severe  engine  damage  due  to  not  properly

maintaining the engine oil.

Driver Assist — If Equipped

Push and release the 

up

 or 

down

 arrow button

until Driver Assist is highlighted in the instru

-

ment cluster display.

Adaptive Cruise Control and LaneSense:

Driver  Assist  Screen  shows  the  current
status of both the Adaptive Cruise Control
(ACC) and the LaneSense systems

Popup messages also indicate the status of
the system and/or the conditions that need
to be met

2020_CHRYSLER_PACIFICA_HYBRID_SUPP_USA=GUID-876DAAE8-C65F-4BC7-BAA9-813BB1426F1D=1=en=.book  Page 33  

Summary of Contents for Pacifica Hybrid 2020













































































































Reviews:

No comments