background image

UNIT IDENTIFICATION (CONT’D.)

SPARE PARTS LIST FOR ANSI FLANGE HEATERS

Labeling Descriptions

Specific model information such as the unique Chromalox part num-
ber, manufacturing date, third party certifications, etc. can be found by

using the diagram below. For additional information not contained
here, please contact you local Chromalox Sales Office.

9

Flange Size

3"

5"

6"

8"

10"

12"

14"

150# ANSI Flange Gasket

132-017222-015 132-017222-016 132-017222-005 132-017222-007 132-017222-009 132-017222-011 132-017222-013

(1) Set of Flange Bolting & Nuts (rated 150LB*)

168-306161-001 168-306161-002 168-306161-003 168-306161-004 168-306161-005 168-306161-006 168-306161-007

Terminal Housing Cover (E1)

080-013022-001 080-013063-001 080-305809-006 080-305809-008 080-305809-010 080-305809-012 080-305809-014

Blank Service Entrance Plate (E1)

027-014672-001 027-014672-001 080-305942-006 080-305942-008 080-305942-010 080-305942-012 080-305942-014

(1) Set of Cover/Enclosure Bolts & Nuts (E1&E4)

N/A

N/A

168-306161-008 168-306161-008 168-306161-008 168-306161-009 168-306161-009

Terminal Housing Cover (E4)

N/A

N/A

080-305809-006 080-305809-008 080-305809-010 080-305809-012 080-305809-014

Blank Service Entrance Plate (E4)

N/A

N/A

080-305807-006 080-305807-008 080-305807-010 080-305807-012 080-305807-014

Service Entrance Plate Gasket (E4)

N/A

N/A

132-305811-006 132-305811-008 132-305811-010 132-305811-012 132-305811-014

Terminal Housing to Flange Gasket (E4)

N/A

N/A

132-305810-006 132-305810-008 132-305810-010 132-305810-012 132-305810-014

Terminal Housing Cover Gasket (E4)

N/A

N/A

132-305810-006 132-305810-008 132-305810-010 132-305810-012 132-305810-014

Terminal Housing Cover Gasket (E2)

132-305967-004 132-305969-005 132-116937-040 132-116937-044 132-116937-047 132-116937-046 132-116937-050

Terminal Housing Cover (E2)

080-305967-003 080-305969-004 080-306161-021 080-306161-022 080-306161-023 080-306161-024 080-306161-025

(1) Set of Cover/Enclosure Bolts (E2)

N/A

N/A

168-306161-010 168-306161-011 168-306161-012 168-306161-013 168-306161-014

Thermostat Install Kit (Parts to Mount Thermostat-E1)

N/A

N/A

300-306012-009 300-306012-001 300-306012-010 300-306012-012 300-306012-014

Thermostat Install Kit (Parts to Mount Thermostat-E4)

N/A

N/A

300-306012-009 300-306012-001 300-306012-010 300-306012-012 300-306012-014

Thermostat Install Kit (Parts to Mount Thermostat-E2)

N/A

300-306012-005 300-306012-007 300-306012-008 300-306012-011 300-306012-013 300-306012-015

Thermostat (0-100 deg. F)

N/A

300-048518-012 300-048518-012 300-048518-012 300-048518-012 300-048518-012 300-048518-012

Thermostat (60-250 deg. F)

N/A

300-048518-013 300-048518-013 300-048518-013 300-048518-013  300-048518-013  300-048518-013

Thermostat (200-550 deg. F)

N/A

300-048518-014 300-048518-014 300-048518-014 300-048518-014 300-048518-014 300-048518-014

Element Buss Bar 17" (User cut to Length)

N/A

N/A

166-305730-009 166-305730-009 166-305730-009 166-305730-009 166-305730-009

Line Buss Bar 17" (User cut to Length)

N/A

N/A

166-305730-006 166-305730-006 166-305730-006 166-305730-006 166-305730-006

Power Connection Bussing (hardware included)

N/A

N/A

168-306161-015 168-306161-016 168-306161-017 168-306161-018 168-306161-019

Circuit Labels (Pack of 9 unique labels-3 circuits)

168-306161-020

* = Grade SA-325, oiled structural steel.

"TOP" Mark

on flange

Identification

Nameplate

All cautionary

labeling on

cover

Manufacturer's

Nameplate

Additional

third party

labeling

Customer

service

information

label

Summary of Contents for TM Series











Reviews: