Christini AWD 450 Service Manual Download Page 26

Page: 26 / 118

Page 25

Maintenance

ENGINE IDLE SPEED

The engine must be warm for an accurate idle inspection and adjustment. Ten
minutes of stop and go riding is sufficient.

•

Warm up the engine, shift the transmission into neutral and hold the mo-
torcycle upright.

•

Connect a tachometer according to its manufacturer’s instructions.

•

Turn the throttle stop screw to obtain the specified idle speed.

IDLE SPEED: 1,500

IDLE SPEED: 1,500 +

+100 rpm

100 rpm

ENGINE OIL / OIL FILTER

OIL LEVEL INSPECTION

•

Run the engine at idle speed for 3 minutes, then stop it for 3 Minutes.

•

Support the motorcycle in an upright position on a level surface.

•

Remove the oil filter cap/dipstick and wipe the oil with clean cloth.

•

Insert the dipstick without screw in, take it out and check the oil level.

•

If the oil level is lower or near the lower level line on the stick, add recom-
mended oil to the upper level line through the hole.

•

Reinstall the engine oil filter cap

(other viscosities shown in the chart may be used when the average temperature in your
riding area is within the indicated range)

RECOMMENDED ENGINE OIL:

HP4M (with molybdenum additives) 4-stroke oil , or equivalent motor oil

API service classification : SG or higher

JASO T 903 STANDARD :MA or MB, viscosity : SEA 10W -40

OIL CAPACITY

0.67liter at draining

0.70liter at oil filter change

Summary of Contents for AWD 450























































































































Search results

Summary of Contents for AWD 450

Reviews:

Related manuals for AWD 450

Brands by name

Popular brands

Christini AWD 450, Service Manual

Search results

Summary of Contents for AWD 450

Reviews:

Related manuals for AWD 450

Brands by name

Popular brands