Chino KR2000 General Instruction Manual Download | Manualshive

Page: 81 / 136

background image

－

79

－

13.10.2 DNS settings

The DNS server is for converting the address specified with a name into the IP address. When the
addresses of the FTP server, POP3 server, SMTP server, etc. are entered with names, make sure to set
the DNS server.

・

Proceed from the MENU settings.

・

Move the focus to the setting item using direction key.

・

By pressing the ENTER key on the item for setting, the screen moves to the input screen.

By selecting the network settings on the setting menu screen and then selecting the DNS settings, the
following screen is displayed.

■

DNS on/off

・

Select the DNS from ON (enabled) or OFF (disabled).

■

Primary server IP, secondary server IP

・

Enter the address of the DNS server. If the primary server is not found, use the address of the
secondary server. When there is only one DNS server, it is no problem not to enter any address to
the secondary server.

«
...
79
80
81
82
83
...
»

Summary of Contents for KR2000









































































































































Reviews:

No comments

Related manuals for KR2000

RQ-L31 - Cassette Dictaphone

Brand: Panasonic Pages: 7

Brand: Mini Gadgets Pages: 5

Brand: Mini Gadgets Pages: 5

Brand: ABB Pages: 88

ICD P620 - 512 MB Digital Voice Recorder

Brand: Sony Pages: 56

Brand: RCA Pages: 25

Brand: Palsonic Pages: 37

ScreenMaster RVG200

Brand: ABB Pages: 16

Brand: Magnavox Pages: 128

Brand: Girl tech Pages: 2

Brand: Panasonic Pages: 6

WS 110 - 256 MB Digital Voice Recorder

Brand: Olympus Pages: 14

Brand: Panasonic Pages: 80

Brand: Panasonic Pages: 88

Brand: Panasonic Pages: 2

Brand: Panasonic Pages: 80

Brand: Panasonic Pages: 95

Diga DMR-ES20DEB

Brand: Panasonic Pages: 56

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands