manualshive.com logo in svg

Chinavision RX102, Device Manual

Share
Download
Chinavision RX102 Device Manual Download Page 6

                                                                 

6 

 

Lock the SD card to slot                                        Lock the SIM card to slot 

       

 

7.

 

  Battery and Charger 

Do charge the battery to capacity in 8 -12 hours for first time. Please use the battery and charger provided by the 

manufacturer. This tracker device adopts built-in Li-ion battery, and full battery can standby 80 hours. After first 

use, the battery usually should be charged fully in 3-5 hours.   

Cautions: 

 

For the Li-ion battery, which contains harmful chemicals and may burst, please don’t bump, puncture it violently 

and keep it off fire. 

 

Please charge the battery in time to keep it working normally. 

8.

 

Startup   

 

Put the SIM card or SD card and battery in place. 

 

Turn on the tracker device outdoors by pressing the “on/off” button until the indicator is on. 

 

For first use, please initialize the tracker device and restore it to default setting. (Please refer for instruction 

command.) 

 

In 30 or 60 seconds, the tracker device will begin to work and acquire the GSM signals as well as the GPS 

signals. The indicator will keep flashing, when the device has received the signals. 

( You can observe the LED flashes, know the working status of the device. Please refer to the list: V. LED 

indicator status) 

 

When this tracker device receives GPS signals normally, you can use it and do any setting as the instructions of 

this manual. 

II.

 

Tracker Device Operating Mode 

1.

 

SMS Monitoring Mode   

SMS monitoring mode is the device’s default monitoring mode. User could use the authorized 
telephones as a master, control/monitor the device by sending SMS text messages. We mainly 
discuss this mode in this manual. 

2.

 

GPRS Tracking Mode 

With an 

Internet-connected computer, 

user could also use a professional PC software or service platform to 

control/monitor the device. This mode is called the GPRS monitoring mode. Before using this mode, some 

related internet parameters should be set firstly through the SMS monitoring mode. How to use the GPRS 

tracking mode is beyond the scope of this manual. We only introduce the related GPRS parameter setting in the 

following chapters. 

3.

 

Without SIM Card, GPS Device Track Record Mode 

Summary of Contents for RX102


















Reviews:

No comments

Brands by name

Popular brands

Load more brands