background image

Installation Instructions

 KSA-1022

5

WALL TRACK INSTALLATION

1.

Determine mounting location on wall.

2.

Determine whether wall track accessory will be mounted 
horizontally or vertically. 

WARNING:  

There is a limit on how many components may 

be mounted on each bracket depending on the mounting 
method. Refer to the table below for details.

WARNING:  

The KSA-1022 wall track accessory CANNOT 

be installed horizontally on drywall without wood or steel 
studs.

NOTE:  

It may be necessary to remove cable management 

flaps from wall track accessory in order to expose holes 
to be used for installation.

Vertical Installation using Wood Studs

1.

Using a stud finder or similar method locate stud.

2.

Align the middle mounting holes on mount with stud making 
sure mounting holes are centered on stud. (See Figure 1)

Figure 1

3.

Using wall track accessory (A) as a template, mark location 
of three mounting holes on wall. (See Figure 1)

4.

Drill three 7/64" holes. (See Figure 1)

5.

Install three #12 x 2 1/2" round pan wood screws (F) through 
small center bracket holes and into drilled holes. (See 
Figure 2)

Figure 2

Vertical Installation on Drywall

WARNING:  

Drywall must be at least 1/2" thick in order to 

install wall track accessory.

1.

Using wall track accessory (A) as a template, mark location 
of six mounting holes on wall making sure it will be level. 
(See Figure 3)

Figure 3

Two Mount Maximum 

Three Mount Maximum

Horizontal, dual stud mounting

Horizontal, triple stud mounting

Vertical, drywall mounting

Vertical, single stud mounting

3

4

X 3

X 3

Mounting holes
centered on stud

(A)

(F) x 3

5

(A)

1

2

X 6

X 6

(A)

Summary of Contents for KSA-1022

















Reviews: