background image

 TIL1X2AA / TIL1X3AA / TIL1X4AA / TILVABAA

Installation Instructions

6

Installing First Mount

The TIL1X2AA / TIL1X3AA /TIL1X4AA (Absen Acclaim Series) 

LED wall mounts are designed to be mounted to:

a bare 8" concrete or 8"x8"x16" concrete block wall; or

a 3/4" thickness plywood-backed, 2" x 4" wood studs 

(16" on center minimum) wall with a maximum drywall 

thickness of 5/8"; or

a 3/4" thickness plywood-backed, steel stud wall 

covered with drywall having a maximum thickness of   

5/8". 

Table 1: Fastener Information

1.

Hold furthest left, top wall mount against wall ensuring that 

mounting slot is lined up with center line marked on the wall 

in 

Determining Installation Site

 section. Double-check 

with a level. (See Figure 4)

2.

Mark mounting holes in two top mounting slots along the 

horizontal line marked in Step 3. (See Figure 4)

NOTE:  

The center of the mounting holes are 14.25" apart on-

center. (See Figure 4)

Figure 4

3.

Drill two pilot holes (see Table 1 for size) at each location 

marked in Step 2 (See Figure 4) and follow fastener 

information (appropriate for wall type) located in Table 1.

IMPORTANT ! : 

Refer to 

Fastener Installation Methods 

(located in 

Appendix 

at end of Installation Instructions) 

for details on installing product into various wall types.

4.

Partially install two fasteners into wall, but do NOT 

completely tighten to wall. (See Figure 5)

NOTE:  

Utilizing the two U-shaped installation washers (H) 

allows the installer to pre-install the top mounting 

fasteners and hang the mount from them utilizing the 

mount’s teardrop slots. This allows the weight of the 

mount to be held by the mounting bolts and not the 

installer during installation. 

Figure 5

5.

Hang wall mount, aligning upper teardrop slots over 

fasteners, and adjust side-to-side for proper location. (See 

Figure 5)

NOTE:  

The horizontal slots located along the vertical mount 

pieces indicate the approximate center line of the two 

LED modules. The vertical slots located along the 

horizontal mount pieces indicate the horizontal center 

line of the mount. The slots can be used to hold a tape 

measure tab while measuring. (See Figure 6)

Figure 6

WALL 

TYPE

PILOT 

HOLE

FASTENERS (see PARTS 

drawing)

Drywall 

attached to 

plywood-

backed walls 

/Steel studs

 

Drywall 

attached to 

plywood-

backed walls 

/Wood studs

1/2"

7/32" x 3"

-

 1/4-20 x 2-1/2" hex head lag (not 

included)
- 1/4" washer (not included)
- 1/4-20 Toggler Snaptoggle BB 
(not included)
- 5/16 x 2-1/2" flanged hex head    
lag (

F

)

- 5/16" washer (

J

)

- Installation washer (

H

)

Concrete or 

concrete 

block

3/8" x 3"

- 5/16 x 2-1/2" flanged hex head 
lag (

F

)

- 5/16" washer (

J

)

- Installation washer (

H

)

- Fischer Anchor UX10x60R 

(G)

2

14.25 inches

3

Line showing

slots for top 

mounts in LED wall

center of mounting

[TIL1X2AA shown as example]

4

5

x 2

[TIL1X2AA shown as example]

Indicates 

center line 

of the mount

horizontal 

Indicates approximate
center line between 

two LED modules

 

Summary of Contents for AA Series





















Reviews: