manualshive.com logo in svg

CHIEF 361043, Installation Manual

Share
Download
CHIEF 361043 Installation Manual Download Page 87

STANDARD LADDER ASSEMBLY INSTRUCTION MANUAL
 

 

 

 

Chief industries, Inc. 

 

    Manual P/N 361043   

 

 

 

87 

 

Square the Adjustable Platform Tread Sheet Supports to the Adjustable Platform Sidewall Support 
Brackets and then attach the Adjustable Platform Angle Kicker Supports using 5/16” Bin Bolts and 
5/16” Whiz Nuts so that one end of the Angle Kicker Support is fastened to the Tread Sheet Support 
and the other end is attached to the Sidewall Support Bracket. 

 

(Height Positioning for Adjustable Platform Supporting Components) 

 

Important Note: 

The Adjustable Commercial Eave Platform Assembly is interchangeable and can be 

installed either on the right hand or left hand side of the Ladder Package simply by flipping the 
orientation of the Adjustable Platform Tread Sheet and assembling the Platform Handrails, Platform 
Handrail Posts and Adjustable Platform Post Supports accordingly.  
 
Now construct the Adjustable Commercial Platform Assembly using 5/16” Bin Bolts and Whiz Nuts, 
separate from the Grain Storage Assembly.  Once the Adjustable Platform Assembly is together, lift 
the platform into place aligning the smaller slotted holes in the Tread Sheet to the holes in the Tread 
Sheet Supports and connect them with 5/16” fasteners. 
 

Summary of Contents for 361043

































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands