background image

STANDARD LADDER ASSEMBLY INSTRUCTION MANUAL
 

 

 

 

Chief industries, Inc. 

 

    Manual P/N 361043   

 

 

 

 

STANDARD LIMITED WARRANTY: 

Chief Grain Storage Products 

1.

 

Definitions:

  The following terms, when they appear in the body of this Standard Limited 

Warranty for Grain Bin Products in initial capital letters shall have the meaning set forth 
below: 
A.

 

Accepted Purchase Order shall mean the Purchase Order identified below. 

B.

 

Chief shall mean Chief Agri/Industrial, a division of Chief Industries, Inc. 

C.

 

Original Owner shall beam the original owner identified below. 

D.

 

Product shall mean the Agri/Industrial Equipment as described in the Accepted Purchase 
Order. 

E.

 

Reseller shall mean the authorized Chief Agri/Industrial Equipment dealer identified 
below. 

 

2.

 

Limited Product Warranty

:  Upon and subject to the terms and conditions set forth below, 

Chief hereby warrants to the Reseller and, if different, the Original Owner as follows: 
A.

 

All new Products delivered to the Reseller or the Original Owner by Chief pursuant to the 
Accepted Purchase Order will, when delivered, conform to the specifications set forth in 
the Accepted Purchase Order; 

B.

 

All new Products delivered pursuant to the Accepted Purchase Order will, in normal use 
and service, be free from defects in materials or workmanship; and 

C.

 

Upon delivery, Chief will convey good and marketable title to the Products, free and clear 
of any liens or encumbrances except for, where applicable, a purchase money security 
interest in favor of Chief. 

 

3.

 

Duration of Warranty and Notice Requirements

:  Subject to the Exceptions, Exclusions and 

Limitations set forth below, the warranties set forth in Section 2 above shall apply to all 
covered non-conforming conditions that are discovered within the first sixty (60) months 
following delivery of the Product to the carrier designated by the Reseller and/or the Original 
Owner at Chief’s manufacturing facility in Kearney, Nebraska (the “Warranty Period”) and are 
reported to Chief as provided in Section 4 below within thirty (30) days following discover (a 
“Notice Period). 
 

4.

 

Notice Procedure

:  In order to make a valid warranty claim, the Reseller and/or the Original 

Owner must provide Chief with a written notice of any nonconforming condition discovered 
during the Warranty Period within the applicable Notice Period specified in Section 3 above.  
Said notice must be in writing; be addressed to Chief Industries, Inc., Agri/Industrial Division, 
Customer Service Department, P.O. Box 848, Kearney, NE  68848; and contain the following: 

 

A.

 

 The Customer’s name and address 

B.

 

The Reseller’s name and address 

C.

 

The make and model of the Product in question 

D.

 

The current location of the Product 

E.

 

A brief description of the problem with respect to which warranty coverage is claimed 

F.

 

The date on which the Product was purchased 

Summary of Contents for 361043

































































































































Reviews: