background image

STANDARD LADDER ASSEMBLY INSTRUCTION MANUAL
 

 

 

 

Chief industries, Inc. 

 

    Manual P/N 361043   

 

 

 

65 

 

C.  FARM PLATFORM EAVE ASSEMBLY 

The following is a step by step detail of how to assemble a Farm Eave Platform Assembly for use with 
your Ladder Package installed with your Chief Grain Storage System. 

After the Roof and the first (2) two rings of the Sidewall Stack have been put together, begin by 
determining the position that the Ladder Package will be installed by locating the roof manhole.  After 
you’ve located the correct placement for the ladder assembly begin by drilling (2) two 1/2” holes thru 
the sidewall.  The hole should be drilled on the first and third corrugations, directly below the second 
single punched hole left of the vertical seam nearest the left side of the roof manhole. 
Attach (2) two J-Post ladder brackets to the bin thru the 1/2" drilled holes using 7/16” Bin Bolts and 
7/16” Whiz Nuts making certain to use the sealing washer and flat washer as previously indicated and 
install the Bin Bolt from the inside of the bin. 
 
Next, remove the previously installed Bin Bolt and Whiz nut from the vertical seam immediately under 
the single punched hole to the left of the manhole on the second corrugation and then fasten a Ladder 
Bracket (9396240) to the sidewall.   
 
Next, remove (2) two fasteners from the First Horizontal seam.  One will be located directly below the 
(2) two drilled 1/2" holes and the other located at the bottom of the vertical seam.  Install (2) two 
more Ladder Brackets (9396240) at these locations.  Again, make sure to use the sealing and flat 
washers and to re-insert the same fasteners that you removed but with the Bin Bolt installed from the 
inside. 
 

 

(Detailed View of J-Post and Ladder Bracket Installation) 

Next, begin to position the Adjustable Platform Sidewall Supports to Ring #1 of the Sidewall Stack. 
Start by drilling 1/2” holes through the Sidewall Sheet. Holes should be drilled at the Third, Sixth and 
Eighth corrugations directly above the 

SECOND

 and 

EIGHTH 

hole of the horizontal seam to the right of 

the left-hand vertical seam.   
 

Important Note:

  

If installing the Adjustable Farm Eave Platform Assembly on a fully stiffened bin you

 

will need to install the Adjustable Platform Sidewall Support closest to the ladder over the stiffener 

Summary of Contents for 361043

































































































































Reviews: