3
6. Troubleshooting
Following are a few common problems that may occur during operation. Here are some suggestions
for easy troubleshooting:
A. The unit does not work, no light and the fan does not work
1. Check the connect power and main fuse.
2. Measure the mains voltage on the main connector.
3. Check the power on LED.
B. Not responding to DMX controller
1. DMX LED should be on. If not, check DMX connectors, cables to see if link properly.
2. If the DMX LED is on and no response to the channel, check the address settings and DMX polarity.
3. If you have intermittent DMX signal problems, check the pins on connectors or on PCB of the unit or the
previous one.
4. Try to use another DMX controller.
5. Check if the DMX cables run near or run alongside to high voltage cables that may cause damage or
interference to DMX interface circuit.
C. Some units don’t respond to the easy controller
1. You may have a break in the DMX cabling. Check the LED for the response of the master/ slave mode signal.
2. Wrong DMX address in the unit. Set the proper address.
D. No response to the sound
1. Check the unit that is not receiving DMX signal.
2. Check the unit that is not set to display mode
3. Check microphone to see if it is good by tapping the microphone
E. One of the channels is not working well
1. The stepper motor might be damaged or the cable connected to the PCB is broken.
2. The motor’s drive IC on the PCB might be out of condition.
F. The lamp is cutting out intermittently
1. The lamp is not working well. Check the main voltage either too high or too low.
2. Internal temperature may be too high. Check and if necessary replace the fan on the head.
Warning
l
To prevent or reduce the risk of electrical shock or fire, do not expose the unit to rain or moisture.
l
Never touch bulb with bare fingers as it is very hot after using.
l
Hot lamp explosion hazard. Do not open the unit within five minutes after switching off.
l
Do not start on the unit without bulb enclosure or housing are damaged.
l
The housing, the lenses, or the ultraviolet filter must be replaced if they are visibly damaged.
l
Do not look directly at the light while the bulb is on.
Caution
There are no user serviceable parts inside the unit. Do not open the housing or attempt any
repairs yourself. In the unlikely event your unit may require service, please contact your nearest
dealer.
Installation
The unit should be mounted via its screw holes on the bottom of the base. Use clamps to fix the unit to truss.
Always ensure that the unit is firmly fixed to avoid vibration and slipping while operating. Always ensure that the
structure to which you are attaching the unit is secure and is able to support a weight of 15kgs for each unit.
2. Technical Specification
∞
Power supply
- AC 120V~60Hz
- AC 230/240V~50/60Hz
∞
Lamp
-
ELC3 24V 250W (300 Hrs)
∞
Optical system
- Standard 11° focused beam angle.
- Focus can be adjusted by manual.
∞
Gobo wheel
- Independent gobo wheel with 14 gobos plus open and shutter.
-
Blackout, and strobe speed variable(1~7 flashes per second).
∞
Color wheel
- Independent color wheel with 11 dichroic mirrors plus white.
∞
Movement
- Pan : 540° in 2.8 second.
- Tilt : 270° in 1.6 second.
∞
DMX Channels
- Standard DMX512 signal addressing and can be controlled by any universal DMX controller.
Channel 1 = Shutter
Channel 2 = Gobos
Channel 3 = Colors
Channel 4 = Pan motion
Channel 5 = Tilt motion
∞
Dimension :
290mm x 330mm x 380mm / 11.42in x 12.99in x 14.96in
∞
Weight :
11 kgs / 24.2 lbs
