background image

 
1. Before You Begin 

 

 

1.

 

B

EFORE 

Y

OU 

B

EGIN

 

 

 

What is Included 

 

 

 

 

1 x Abyss™ LED 3.0 

 

1 x Power Cord 

 

1 x Warranty Card 

 

1 x User Manual 

 

 

Unpacking Instructions 

 

 

 

Immediately upon receiving a fixture, carefully unpack the carton. Check the contents to ensure 
that all parts are included and received in good condition.  

 

 

Claims 

 

 

 

If the container or the material inside the container (this product and any accessory included) 
appears damaged from shipping or shows signs of mishandling, contact the shipper immediately, 
not CHAUVET®, upon receipt. Failure to do so in a timely manner may invalidate your claim with 
the carrier. In addition, retain the container and all the packing material for inspection. 
For other issues, such as missing components or parts, damage not related to shipping, or 
concealed damage, you should make claims to CHAUVET® within seven (7) days of receiving 
the merchandise. 
 

Manual Conventions 

 

 

 

CHAUVET® manuals use the following conventions to differentiate certain types of information 
from regular text. 

 

 

 

C

ONVENTION

 

M

EANING

 

[10] 

A DIP switch to be configured  

<Menu> 

A key to be pressed on the fixture’s control panel 

1~512 

A range of values 

50/60 

A set of values of which only one can be chosen 

Settings 

A menu option not to be modified (for example, showing the operating 
mode/current status) 

MENU >

 

Settings

 

A sequence of menu options to be followed 

ON 

A value to be entered or selected 

 

 

 

Icons 

 

This manual uses the following icons to indicate information requiring special attention. 

 

 

 

I

CONS

 

M

EANING

 

 

This paragraph contains critical installation, configuration or operation 
information. Failure to comply with this information may render the fixture 
partially or completely inoperative, cause damage to the fixture, or cause 
harm to the user. 

 

This paragraph contains important installation or configuration information. 
Failure to comply with this information may prevent the fixture from 
functioning correctly. 

 

This paragraph reminds you of useful information. 

 

 

 

Summary of Contents for Abyss LED 3.0
















Reviews: