Chassis Plans ATXN-5520 Technical Reference Download Page 75

Page: 75 / 152

ATXN-5520 / WTM7026 Technical Reference

Advanced Setup

5-7

Chassis Plans

Execute-Disable Bit Capability

The Setup screen displays the system option:

Execute-Disable Bit Capability [Enabled]

Available options are:

Disabled

Enabled

Intel(R)

HT Technology

HT means Hyper-Threading and the Setup screen displays the system option:

Intel(R) HT Technology [Enabled]

Available options are:

Enabled

Disabled

Active Processor Cores

The Setup screen displays the system option:

Active Processor Cores [ALL]

Available options are:

All

1, 2, 3, 4 or 5

A20M

The Setup screen displays the system option:

A20M [Disabled]

Available options are:

Disabled

Enabled

Intel(R)

SpeedStep ™ Tech

The Setup screen displays the system option:

Intel(R) SpeedStep™ Tech [Disabled]

Available options are:

Disabled

Enabled

Summary of Contents for ATXN-5520

























































































































































Search results

Summary of Contents for ATXN-5520

Reviews:

Related manuals for ATXN-5520

Brands by name

Popular brands

Chassis Plans ATXN-5520, Technical Reference

Search results

Summary of Contents for ATXN-5520

Reviews:

Related manuals for ATXN-5520

Brands by name

Popular brands