background image

8

Burner Flame Check

• Remove cooking grates and flame tamers. Light burners, rotate 

knobs from 

HIGH

 to 

LOW

. You should see a smaller flame in

 

LOW

 position than seen on 

HIGH

. Perform burner flame check 

on sideburner, also. Always check flame prior to each use. If 
only low flame is seen refer to "Sudden drop or low flame" in 
the 

Troubleshooting Section

.

HIGH

LOW

Match-Lighting

 Do not lean over grill while lighting.

1. Open lid. 

Turn 

ON

 gas at LP cylinder.

 

3. 

Push in and turn far right or far left burner knob to the 

     HIGH

burner lights and stays lit.

4. 

Light adjacent burners in sequence by pushing knobs in and 

turning to the      

HIGH

 position.

Turning Grill Off

• Turn all knobs to the 

     OFF 

position. Turn LP cylinder 

OFF

 by 

turning hand-wheel clockwise to a full stop.

Ignitor Check

• Turn gas off at LP cylinder.

 Press and hold electronic ignitor 

button.  "Click" should be heard and spark seen each time 
between each collector box or burner and electrode. See 

"Troubleshooting"

 if no click or spark.

Valve Check

•  Important: Make sure gas is off at LP cylinder before 

checking valves

.  Knobs lock in  

position. To check 

valves, first push in knobs and release, knobs should spring 
back. If knobs do not spring back, replace valve assembly 
before using grill. Turn knobs to

 LOW

 position then turn back to  

position. Valves should turn smoothly.  

Hose Check

• 

Before each use, check to see if hoses are cut or worn or kinked. 

Replace damaged hoses before using grill. Use only 
valve/hose/regulator specified by manufacturer.

General Grill Cleaning 

• Do not mistake brown or black accumulation of grease and 

smoke for paint.  Interiors of gas grills are not painted at the 
factory 

(and should never be painted)

. Apply a strong solution 

of detergent and water or use a grill cleaner with scrub brush 
on insides of grill lid and bottom. Rinse and allow to completely 
air dry. 

Do not apply a caustic grill/oven cleaner to painted 

surfaces.

 

• 

Plastic parts: 

Wash with warm soapy water and wipe dry.

 

Do not use citrisol, abrasive cleaners, degreasers or a 

concentrated grill cleaner on plastic parts. Damage to and 
failure of parts can result. 

• Porcelain surfaces: 

Because of glass-like composition, most 

residue can be wiped away with baking soda/water solution or 
specially formulated cleaner.

 

Use nonabrasive scouring powder 

for stubborn stains.

• Painted surfaces: 

Wash with mild detergent or nonabrasive 

cleaner and warm soapy water. Wipe dry with a soft 
nonabrasive cloth.

• Stainless steel surfaces: 

To maintain your grill’s high quality 

appearance, wash with mild detergent and warm soapy water 
and wipe dry with a soft cloth after each use. Baked-on grease 
deposits may require the use of an abrasive plastic cleaning 
pad. Use only in direction of brushed finish to avoid damage. 
Do not use abrasive pad on areas with graphics.

• Cooking surfaces:

 If a bristle brush is used to clean any of

the grill cooking surfaces, ensure no loose bristles remain on
cooking surfaces prior to grilling. It is not recommended to
clean cooking surfaces while grill is hot.

OFF 

 

OFF 

 

CAUTION

If ignition does NOT occur in 5 seconds, turn the 
burner controls      OFF, wait 5 minutes and repeat the 
lighting procedure. If the burner does not ignite with 
the valve open, gas will continue to flow out of the 
burner and could accidently ignite with risk of injury.

Turn controls and gas source or tank OFF when not 

in use.

WARNING

Sideburner Ignitor Lighting

 

 Do not lean over grill while lighting.

1. Open sideburner lid. 

Turn 

ON

 gas at LP cylinder.

2. 

Turn sideburner knob to the 

     HIGH

 position, push and hold

ELECTRONIC IGNITOR

 button.

3. 

If sideburner does NOT light within 5 seconds, turn knob to       

OFF

, wait 5 minutes, then 

Sideburner Match Lighting

1. Open sideburner lid. 

Turn 

ON

2. 

Place lit match near burner.

3. 

Turn sideburner knob to the

Be sure burner lights and
stays lit.

2.

 Place match into match holder (hanging from side panel of 

grill). Light match; then light burner by placing match through 
the match light hole on right or left side of grill.

HIGH

 position.

gas at LP cylinder.

repeat lighting procedure.

position, depending on match light hole selected. Be sure

NOTE: Your grill may NOT be equipped with a Sideburner!

Summary of Contents for 463270913

































Reviews: