Burner Flame Check
• Remove cooking grates and flame tamers. Light burners, rotate
knobs from
HI
to
LOW
. You should see a smaller flame in
LOW
position than seen on
HI
. Perform burner flame check
on sideburner, also. Always check flame prior to each use. If
only low flame is seen refer to "Sudden drop or low flame" in
the
Troubleshooting Section
.
HI
LOW
Match-Lighting
s
Do not lean over grill while lighting.
1. Open lid.
Turn
ON
gas at LP cylinder.
3.
Push in and turn far right or far left burner knob to the
HI
burner lights and stays lit.
4.
Light adjacent burners in sequence by pushing knobs in and
turning to the
HI
position.
Turning Grill Off
• Turn all knobs to the
OFF
position. Turn LP cylinder
OFF
by turning
hand-wheel clockwise to a full stop.
Ignitor Check
• Turn gas off at LP cylinder.
Press and hold electronic ignitor
button. "Click" should be heard and spark seen each time
between each collector box or burner and electrode. See
"Troubleshooting"
if no click or spark.
Valve Check
• Important: Make sure gas is off at LP cylinder before
checking valves
. Knobs lock in
position. To check
valves, first push in knobs and release, knobs should spring
back. If knobs do not spring back, replace valve assembly
before using grill. Turn knobs to
LOW
position then turn back to
position. Valves should turn smoothly.
Hose Check
•
Before each use, check to see if hoses are cut or worn or kinked.
Replace damaged hoses before using grill. Use only
valve/hose/regulator specified by manufacturer.
General Grill Cleaning
• Do not mistake brown or black accumulation of grease and
smoke for paint. Interiors of gas grills are not painted at the
factory
(and should never be painted)
. Apply a strong solution
of detergent and water or use a grill cleaner with scrub brush
on insides of grill lid and bottom. Rinse and allow to completely
air dry.
Do not apply a caustic grill/oven cleaner to painted
surfaces.
•
Plastic parts:
Wash with warm soapy water and wipe dry.
s
Do not use citrisol, abrasive cleaners, degreasers or a
concentrated grill cleaner on plastic parts. Damage to and
failure of parts can result.
• Porcelain surfaces:
Because of glass-like composition, most
residue can be wiped away with baking soda/water solution or
specially formulated cleaner.
Use nonabrasive scouring powder
for stubborn stains.
• Painted surfaces:
Wash with mild detergent or nonabrasive
cleaner and warm soapy water. Wipe dry with a soft
nonabrasive cloth.
• Stainless steel surfaces:
To maintain your grill’s high quality
appearance, wash with mild detergent and warm soapy water
and wipe dry with a soft cloth after each use. Baked-on grease
deposits may require the use of an abrasive plastic cleaning
pad. Use only in direction of brushed finish to avoid damage.
Do not use abrasive pad on areas with graphics.
• Cooking surfaces:
If a bristle brush is used to clean any of
the grill cooking surfaces, ensure no loose bristles remain on
cooking surfaces prior to grilling. It is not recommended to
clean cooking surfaces while grill is hot.
OFF
OFF
CAUTION
If ignition does NOT occur in 5 seconds, turn the
burner controls OFF, wait 5 minutes and repeat the
lighting procedure. If the burner does not ignite with
the valve open, gas will continue to flow out of the
burner and could accidently ignite with risk of injury.
Turn controls and gas source or tank OFF when not
in use.
WARNING
Sideburner Ignitor Lighting
s
Do not lean over grill while lighting.
1. Open sideburner lid.
Turn
ON
gas at LP cylinder.
2.
Turn sideburner knob to the
HI
position, push and hold
ELECTRONIC IGNITOR
button.
3.
If sideburner does NOT light within 5 seconds, turn knob to
OFF
,
wait 5 minutes, then
Sideburner Match Lighting
1. Open sideburner lid.
Turn
ON
2.
Place lit match near burner.
3.
Turn sideburner knob to the
Be sure burner lights and
stays lit.
2.
Place match into match holder (hanging from side panel of
grill). Light match; then light burner by placing match through
the match light hole on right or left side of grill.
HI
position.
8.
For grills equipped with ELECTRONIC IGNITION at
Repeat steps 4 through 6 to light each burner.
9.
Once each burner has ignited, turn knobs to desired setting.
Ignitor Lighting (continued)
each burner:
gas at LP cylinder.
repeat lighting procedure.
position, depending on match light hole selected. Be sure
NOTE: Your grill may NOT be equipped with a Sideburner!
8
