background image

100892 - 4500W OPEN FRAME INvERTER

CONTROLS AND FEATURES

15

FCC Statement

1.  This device complies with Part 15 of the FCC Rules. Operation 

is subject to the following two conditions: 

1a. This device may not cause harmful interference.

1b. This device must accept any interference received, 

including interference that may cause undesired 
operation.

2.  Changes or modifications not expressly approved by the party 

responsible for compliance could void the user’s authority to 
operate the equipment.

 

NOTICE

This equipment has been tested and found to comply with 
the limits for a Class B digital device, pursuant to Part 15 
of the FCC Rules. These limits are designed to provide 
reasonable protection against harmful interference in a 
residential installation. This equipment generates, uses and 
can radiate radio frequency energy and if not installed and 
used in accordance with the instructions, may cause harmful 
interference to radio communications. However, there is 
no guarantee that interference will not occur in a particular 
installation. If this equipment does cause harmful interference 
to radio or television reception, which can be determined by 
turning the equipment off and on, the user is encouraged to 
try to correct the interference by one or more of the following 
measures:

 

Reorient or relocate the receiving antenna.

 

Increase the separation between the equipment and 
receiver.

 

Connect the equipment into an outlet on a circuit different 
from that to which the receiver is connected.

Consult dealer or an experienced radio/TV technician for help.

Parts Included

Accessories

Battery Charging Cables

 ...........................................

1

Dual Port USB Adapter (5v/2.4A)

 ..................................

1

Engine Oil

 ......................................

18.6 fl. oz. (550 ml)

Oil Funnel

 ...........................................................

1

Summary of Contents for 100892








































Reviews: