![background image](http://html.mh-extra.com/html/champion/100641/100641_operators-manual_2588418007.webp)
7
100641 - ChAiNSAw
iMPORTANT SAfETY iNSTRUCTiONS
–
Only use wedges made of wood or plastic. Do not use metal to
hold a cut open.
–
Follow the manufacturer’s sharpening and maintenance
instructions for the saw chain.
–
Only use replacement bars and chains specified by the
manufacturer or the equivalent. These are available from
Champion or other qualified service dealer. Use of any
unauthorized parts or accessories could lead to serious injury
to the operator or damage to the chainsaw and will void the
warranty.
–
Use devices that reduce the risks associated with
kickback,such as low-kickback chains, guide bar nose guards,
chain brakes and low-kickback guide bars. There are no other
replacement components for achieving kickback protection in
accordance with CSA Z62.3.
–
A low-kickback saw chain is a chain that has met the kickback
performance requirements of ANSI/OPEI B175.1-2012
when tested according to the provisions specified in ANSI/
OPEIB175.1-2012. A low-kickback saw chain is a chain that is
also in accordance with CSA Z62.3. Do not use a replacement
saw chain unless it has met these requirements for this
specific model or has been designated as a low-kickback
replacement saw chain in accordance with ANSI/OPEI B175.1-
2012. As saw chains are sharpened, some of the low-kickback
qualities are lost and extra caution should be used.
–
Do not install a bow guide on this chainsaw. Bow guides have
larger kickback zones, which increase the chance of kickback
and serious injury. This increase is not significantly reduced
by using a low-kickback saw chain. Using a bow guide on this
chainsaw is extremely dangerous.
Other Safety warnings
wARNiNG
–
Follow all maintenance instructions in this manual.
–
All service, other than the maintenance procedures
described in this manual, should be performed by a
Champion qualified service dealer.
–
Do not use the chainsaw if it is not working correctly, has
been dropped, damaged, left outdoors or dropped into
water. Have the chainsaw serviced by a Champion qualified
service dealer.
Before inspecting, servicing, cleaning, storing, transporting or
replacing any parts on the chainsaw:
1. Stop the chainsaw.
2. Make sure all moving parts have stopped.
3. Allow the chainsaw to cool.
4. Disconnect the spark plug wire.
–
Secure the chainsaw while transporting.
–
Always use the scabbard on the guide bar and saw chain
during transportation and storage.
–
Always store the chainsaw and fuel in a cool, dry and well-
ventilated space. Do not store fuel, or a chainsaw with fuel in
the tank, indoors where fumes may reach open flames (pilot
lights, etc.) or sparks (switches, electrical motors, etc.).
–
Store the chainsaw in a dry place, secured or at a height to
prevent unauthorized use or damage. Keep the chainsaw out of
the reach of children.
–
Never douse or squirt the chainsaw with water or any other
liquid. Keep handles dry, clean and free from debris, oil,
fuel and grease. Clean the chainsaw after each use. Refer
to Cleaning and Storage. Do not use solvents or strong
detergents.
–
Keep these instructions.
Refer to them often and use them
to instruct other users. If you loan this chainsaw to others, also
loan them these instructions.
wARNiNG
This spark ignition system complies with the Canadian
standard ICES-002
NOTiCE
For users on U.S. Forest Land and in the states of
California, maine, Oregon and Washington.
All U.S.
Forest Land and the state of California (Public Resources
Codes 4442 and 4443), Oregon and Washington require, by
law that certain internal combustion engines operated on
forest brush and/or grass-covered areas be equipped with
a spark arrestor, maintained in effective working order, or
the engine be constructed, equipped and maintained for the
prevention of fire. Check with your state or local authorities
for regulations pertaining to these requirements. Failure to
follow these requirements could subject you to liability or a
fine. This chainsaw is factory equipped with a spark arrestor.
Replacement requires a Muffler Assembly, installed at a
Champion Parts & Repair Service Center.