background image

100593 - 3200 PORTAbLE POwER STATiON

iMPORTANT SAfETY iNSTRUCTiONS

6

 

wARNiNG

 

Do not use a Power Station or appliance that is damaged 
or modified. Damaged or modified internal batteries may 
exhibit unpredictable behavior resulting in fire, explosion or 
risk of injury.

 

Do not remove cover. No user serviceable parts inside.

 

Do not tamper or disassemble the Power Station to attempt 
service or replace the battery. Incorrect reassembly may 
result in a risk of fire, electric shock or personal injury. 

 

For service information please contact our Champion 
Technical Support Team at 1-877-338-0999. Please have 
your serial number and model number available when 
service, repair or replacement is required.

 

Never place fingers or hands inside the product.

 

wARNiNG

 

To reduce the risk of injury or damage, avoid contact with 
any hot surface.

 

Do not use the Power Station near sources of high heat or 
fire. Exposure to fire or temperature above 266°F (130°C) 
may cause explosion.

 

Do not discharge the Power Station battery in 
temperatures below 5°F (-15°C) or above 104°F (40°C).

 

Do not allow fluids to flow into the Power Station. Corrosive 
or conductive fluids, such as seawater, certain industrial 
chemicals, and bleach or bleach containing products, etc., 
can cause a short circuit.

 

Follow all charging instructions and do not charge the 
Power Station outside the temperature range specified in 
the instructions. Charging improperly or at temperatures 
outside the specified range may damage the battery and 
increase the risk of fire.

When charging the Power Station:

 

Always charge the Power Station’s internal battery in a  
well-ventilated area.

 

Do not use the AC charging cable outdoors.

 

Do not expose AC charging cable to oil, oil vapor, grease, 
gasoline, gasoline vapors or other caustic substances that may 
damage the AC charging cable.

 

Do not charge the internal battery below 32°F (0°C) or above 
113°F (45°C).

 

Do not charge Power Station in rain, snow, damp or wet 
locations.

 

Do not overcharge the Power Station internal battery.

 

Always connect to properly grounded outlets.

 

Never use Power Station or charger in the presence of 
explosive atmospheres (gaseous fumes, dust or flammable 
materials).

 

Never leave the Power Station unattended while charging. 
If the internal battery smokes, or gives off an odor during 
charging, terminate charging immediately.

 

During charging, if the Power Station battery becomes hot 
to the touch, stop charging. Allow battery to cool before 
resuming.

 

Always unplug charger when not in use.

 

To reduce the risk of electric shock, always unplug charger 
before cleaning or maintenance. Do not allow water to flow 
into plug. Use a Ground Fault Circuit Interrupter (GFCI) to 
reduce shock hazards.

Grounding Information:

 

The Power Station must be grounded. This product is equipped 
with a cord having a grounding conductor and grounding 
plug. The plug must be plugged into an outlet grounded in 
accordance with all local codes and ordinances.

 

Improper connection of the Power Station grounding conductor 
can result in a risk of electric shock. Check with a qualified 
electrician if you are in doubt as to whether the product is 
properly grounded. 

 

Do not modify the plug provided with the Power Station – if it 
will not fit into the outlet, have a proper outlet installed by a 
qualified electrician.

When storing the Power Station:

 

This Power Station is intended to be stored indoors and shall 
not be stored or left outdoors when not in use.

 

Do not stack any items on top of the Power Station during 
storage. 

 

Store your Power Station and charger in a cool, dry place 
between -4°F (-20°C) and 104°F (40°C). 

 

Do not store Power Station where temperatures may exceed 
120°F (50°C) such as in direct sunlight, in a vehicle or metal 
buildings especially during the summer.

 

Do not store the Power Station near sources of high heat or 
fire.

 

Do not store the Power Station when discharged to 20% or 
less state of charge (SOC).

 

Lithium batteries must be charged regularly to perform well. 
The Power Station must be fully charged by you at least once 
every 6 months (180 days).

Summary of Contents for 100593






























Reviews: