background image

5

  

REV 92221-20120417

ENGLISH

 

92221

Training

1 .  Read the Operator’s Manual completely before 

attempting to use this log splitter .

2 .  Do not allow anyone to operate your log splitter who 

has not read the Operator’s Manual or has not been 
instructed on the safe use of the log splitter .

3 .  Never allow children or untrained adults to operate 

this machine .

4 .  Many accidents occur when more than one (1) 

person operates the log splitter . If a helper is 
assisting in loading logs to be split, never actuate 
controls until helper is clear of the area .

5 .  Never allow anyone to ride on the machine .
6 .  Never transport cargo on the log splitter .
7 .  High fluid pressures are developed in hydraulic 

log splitters . Pressurized hydraulic fluid escaping 
through a pin hole opening can puncture skin 
and cause sever blood poisoning . Therefore, the 
following instructions should be heeded at all times .
a .  Do not operate the unit with frayed, kinked, 

cracked or damaged hoses, fittings, or tubing .

b .  Stop the engine and relieve hydraulic system 

pressure before changing or adjusting fittings, 
hoses, tubing, or other system components .

c .  Do not adjust the pressure settings of the pump 

or valve .

d .  Do not check for leaks with your hand . Leaks 

can be detected by passing cardboard or wood 
over the suspected area . Look for discoloration . 
If injured by escaping fluid, see a doctor at 
once . Serious infection or reaction can develop 
if proper medical treatment is not administered 
immediately .

8 .  Keep the operator zone and adjacent area clear for 

safe, secure footing .

9 .  If your log splitter is equipped with an internal-

combustion engine and intended for use near any 
unimproved forest, brush, or grass covered land, 
the engine exhaust should be equipped with a spark 
arrestor . Make sure you comply with local, state, 
and federal codes . Take appropriate fire-fighting 
equipment with you .

10 . Log splitters should be used only for splitting 

wood . Do not use for other purposes unless the 
manufacturer provides attachments and instructions .

SAFETy RULES

Preparation

1 .  Be thoroughly familiar with all controls and with 

proper use of the equipment .

2 .  Safety Gear:

a .  Always wear safety shoes or heavy boots when 

operating the machine .

b .  Always wear safety glasses or goggles when 

operating the machine .

c .  Never wear jewelry or loose-fitting clothing that 

might become entangled in moving or rotating 
parts of the machine .

3 .  Make sure the splitter is on a level surface . Block 

tires and ensure support leg is secure to prevent 
unintended movement of the log splitter during 
operation .
a .  Always operate the splitter from the 

manufacturer’s indicated operator zone .

4 .  Logs to be split on ram-type units should be cut as 

squarely as possible .

5 .  Fuel:

a .  Use an approved fuel container .
b .  Never add fuel to a running or hot engine .
c .  Fill fuel tank outdoors with extreme care . Never 

fill fuel tank indoors .

d .  Replace gasoline cap securely and clean up any 

spilled fuel .

Summary of Contents for 92221































Reviews: