Champion Power Equipment 92221 Owner'S Manual & Operating Instructions Download Page 28

Champion Power Equipment, Inc. (CPE),  

The California Air Resources Board (CARB) and the United States Environment Protection Agency (U.S. EPA.) 

Emission Control System Warranty  

 
Your Champion Power Equipment (CPE) engine complies with both the U.S. EPA and state of California Air 
Resources Board (CARB) emission regulations.  
 

YOUR WARRANTY RIGHTS AND OBLIGATIONS: 

 
The California Air Resources Board, US EPA AND CPE are pleased to explain the Federal and California Emission 
Control Systems Warranty on your 2012 small off-road engine and engine powered equipment. In California, new, 
small off-road engines and new equipment that use small off-engines must be designed, built and equipped to meet 
the State’s stringent anti smog standards. In the other states, new engines and equipment must be designed, built 
and equipped, at the time of sale, to meet U.S. EPA regulations for small non-road engines. CPE warrants the 
emission control system on your small off-road engine and equipment for the period of time listed below, provided 
there has been no abuse, neglect, unapproved modification, or improper maintenance of your equipment. 
 
Your emission control system may include parts such as the carburetor, fuel-injection system, the ignition system, 
catalytic converter and fuel lines. Also included may be hoses, belts, connectors and other emission related 
assemblies. Where a warrantable condition exits, CPE will repair your small off-road engine at no cost to you 
including diagnosis, parts and labor. For engines less than or equal to 80cc, only the fuel tank and fuel line is 
subject to the evaporative emission control warranty requirements of this section. 
 

MANUFACTURER’S EMISSION CONTROL SYSTEM WARRANTY COVERAGE:

 

 
 This emission control system is warranted for two years, subject to provisions set forth below. If, during the 
warranty period, emission related part on your engine is defective in materials or workmanship, the part will be 
repaired or replaced by CPE. 
 

OWNER WARRANTY RESPONSIBILITIES: 

As the small off-road engine owner, you are responsible for the performance of the required maintenance listed in 
your Owner’s Manual. CPE recommends that you retain all your receipts covering maintenance on your small off-
road engine, but CPE cannot deny warranty solely for the lack of receipts or for your failure to ensure the 
performance of all scheduled maintenance. 
 
As the small off-road engine owner, you should however be aware that CPE may deny you warranty coverage if 
your small, off-road engine or a part has failed due to abuse, neglect, improper maintenance or unapproved 
modifications.  
 
You are responsible for presenting your small off-road engine to an Authorized CPE service outlet  or alternate 
service outlet as described in (3)(f.) below, CPE dealer or CPE, Santa Fe Springs, Ca. as soon as a problem exists. 
The warranty repairs should be completed in a reasonable amount of time, not to exceed 30 days.  
 
If you have any questions regarding your warranty rights and responsibilities, you should contact: 
 

Champion Power Equipment, Inc. 

Customer Service 

10006 Santa Fe Springs Road 

Santa Fe Springs, CA 90670 

1-877-338-0999 

Summary of Contents for 92221































Reviews: