background image

100790 - 4200 PSI PRESSURE WAShER

IMPORTANT SAfETY INSTRUCTIONS

5

 

WARNING

NEVER spray flammable liquids or use pressure washer in 
areas containing combustible dust, liquids, or vapor.

NEVER operate this machine in a closed building or in or near 
an explosive environment.

 

DO NOT remove fuel tank cap or fill fuel tank while engine 
is hot or running (allow engine to cool two minutes before 
refueling). Always fill the tank slowly.

 

NEVER disconnect the high pressure discharge hose from 
the machine while the system is pressurized.

 

WARNING

Rapid retraction of the recoil cord will pull hand and arm 
towards the engine faster than you can let go. Unintentional 
startup can result in entanglement, traumatic amputation or 
laceration. Broken bones, fractures, bruises or sprains could 
result.

When starting engine, pull the recoil cord slowly until 
resistance is felt and then pull rapidly to avoid kickback.

DO NOT start or stop the engine with electrical devices 
plugged in and turned on.

 

DANGER

Keep clear of nozzle.

DO NOT point the spray wand at a person, an animal or 
yourself.

Always wear safety glasses or goggles and protective 
equipment (hearing protection, gloves, rubber boots, protective 
clothing) when operating or performing maintenance.

 

NEVER put hand or fingers over the spray tip while 
operating the unit.

 

NEVER try to stop or deflect leaks with any body part.

 

ALWAYS engage the trigger safety latch in the safe position 
when spraying is stopped even if only for a few moments.

 

WARNING

Always wear eye protection with side shields marked to 
comply with ANSI Z87.1.

Following this rule will reduce the risk of serious personal 
injury.

 

NOTICE

Improper treatment or use of the pressure washer can damage 
it, shorten its life and void your warranty.

Use the pressure washer only for intended uses.

Operate only on level surfaces.

DO NOT expose pressure washer to excessive moisture, dust, 
or dirt.

DO NOT allow any material to block the cooling slots.

DO NOT use the pressure washer if:

 

Equipment sparks, smokes or emits flames

 

Equipment vibrates excessively

 

DANGER

Risk of injection or injury. High pressure jets can be dangerous 
if subject to misuse.

 

DO NOT direct discharge stream at persons, animals, 
electrical devices, or the machine itself.

 

ALWAYS point spray gun in safe direction. Every time you 
stop the engine, squeeze trigger of spray gun to relieve any 
trapped pressure.

 

NOTICE

ONLY use cold water.

 

NOTICE

Water under high pressure can damage fragile surfaces.

 

ALWAYS: practice on a inconspicuous test area to 
understand when damage may occur. 

 

DO NOT: Point spray gun at glass.

 

NEVER: Point the spray nozzle at persons, animals, 
electrical devices, plants or the machine itself.

 

WARNING

Use of pressure washers can create wet walking surfaces. 
While using a pressure washer, forces from the gun can cause 
you to loose footing and fall.

 

Use only on a level surface.

 

Make sure there is proper drainage to dissipate water.

 

DO NOT: use on elevated surface where kickback could 
result in a serious fall.

 

ALWAYS grasp the gun with two hands to prevent potential 
injury do to high pressure from gun.

Summary of Contents for 100790







































Reviews: