background image

CHAMPION POWER EQUIPMENT, INC. (CPE), 

THE UNITED STATES ENVIRONMENTAL PROTECTION AGENCY (U.S. EPA) 

AND THE CALIFORNIA AIR RESOURCES BOARD (CARB) EMISSION CONTROL SYSTEM WARRANTY

Your Champion Power Equipment (CPE) engine complies with both the U.S. EPA and state of California Air Resources Board 
(CARB) emissions regulations.

YOUR WARRANTY RIGHTS AND OBLIGATIONS:

The US EPA, California Air Resources Board, and CPE are pleased to explain the Federal and California Emission Control Systems warranty 
on your 2020 small off-road engine (SORE) and equipment. In the United States and California, new small off-road engines (SORE) and new 
equipment that use small off-road engines (SORE) must be designed, built and equipped to meet the State’s stringent anti-smog standards.

CPE must warrant the emission control system on your small off-road engine (SORE) and equipment for the period of time listed below, 
provided there has been no abuse, neglect or improper maintenance of your small off-road engine (SORE) and equipment leading to the 
failure of the emission control system.

Your emission control system may include parts such as the carburetor, fuel-injection system, the ignition system, catalytic converter, fuel 
tanks, fuel lines (for liquid fuel and fuel vapors), fuel caps, valves, canisters, filters, clamps, connectors, and other associated components. 
Also included may be hoses, belts, and other emission related assemblies. Where a warrantable condition exits, CPE will repair your small 
off-road engine (SORE) and equipment at no cost to you including diagnosis, parts and labor.

MANUFACTURER’S WARRANTY COVERAGE:

This Emissions Control System is warranted for two years. If any emissions-related part on your small off-road engine (SORE) and 
equipment is defective, the part will be repaired or replaced by CPE.

OWNER WARRANTY RESPONSIBILITIES:

As the small off-road engine (SORE) and equipment owner, you are responsible for the performance of the required maintenance listed 
in your Owner’s Manual. CPE recommends that you retain all your receipts covering maintenance on your small off-road engine (SORE) 
and equipment, but CPE cannot deny warranty coverage solely for the lack of receipts or for your failure to ensure the performance of all 
scheduled maintenance.

As the small off-road engine (SORE) and equipment owner, you should be aware that CPE may deny you warranty coverage if your small 
off-road engine (SORE) and equipment or a part has failed due to abuse, neglect, improper maintenance or unapproved modifications.

You are responsible for presenting your small off-road engine (SORE) and equipment to an Authorized CPE service outlet or alternate 
service outlet as described in (3)(f.) below, CPE dealer or CPE, Santa Fe Springs, Ca. as soon as a problem exists. The warranty repairs 
shall be completed in a reasonable amount of time, not to exceed 30 days.

If you have any questions regarding your warranty coverage, you should contact:

Champion Power Equipment, Inc. 

Customer Service 
12039 Smith Ave. 

Santa Fe Springs, CA 90670 

1-877-338-0999 

[email protected]

Summary of Contents for 100536





























Reviews: