background image

30

OPERATION

IMPORTANT INSTALLATION INSTRUCTIONS

To reduce the risk of SEVERE INJURY or DEATH:

WARNING 

1.  READ AND FOLLOW ALL WARNINGS AND 

INSTRUCTIONS.

2.  ALWAYS keep remote controls out of reach of 

children. NEVER permit children to operate or play with 
garage door control push buttons or remote controls.

3.  ONLY activate garage door when it can be seen clearly, 

it is properly adjusted, and there are no obstructions 
to door travel.

4.  ALWAYS keep garage door in sight until completely 

closed. NO ONE SHOULD CROSS THE PATH OF THE 
MOVING DOOR.

5.  NO ONE SHOULD GO UNDER A STOPPED, PARTIALLY 

OPEN DOOR.

6.  If possible, use emergency release handle to disengage 

trolley ONLY when garage door is CLOSED. Weak or 
broken springs or unbalanced door could result in an 
open door falling rapidly and/or unexpectedly, causing 
SEVERE INJURY or DEATH.

7.  NEVER use emergency release handle unless garage 

doorway is clear of persons and obstructions.

8.  NEVER use handle to pull garage door open or closed. 

If rope knot becomes untied, you could fall.

  9.  If one control (force or travel limits) is adjusted, the 

other control may also need adjustment.

10.  After ANY adjustments are made, the safety reversal 

system MUST be tested.

11.  Safety reversal system MUST be tested every month. 

Garage door MUST reverse on contact with 1-1/2" 
(3.8 cm) high object (or a 2x4 laid fl at) on the fl oor. 
Failure to adjust the garage door opener properly may 
cause SEVERE INJURY or DEATH.

12.  ALWAYS KEEP GARAGE DOOR PROPERLY 

BALANCED (see page 3). An improperly balanced 
door may NOT reverse when required and could 
result in SEVERE INJURY or DEATH.

13.  ALL repairs to cables, spring assemblies and other 

hardware, ALL of which are under EXTREME tension, 
MUST be made by a trained door systems technician.

14.  ALWAYS disconnect electric power to garage door 

opener BEFORE making ANY repairs or removing 
covers.

15.  

SAVE THESE 

INSTRUCTIONS.

Using Your Garage Door Opener

Your Security

®

 opener and hand-held remote control 

have been factory-set to a matching code which changes 
with each use, randomly accessing over 100 billion 
new codes. Your opener will operate with up to eight 
Security

®

 remote controls and one Security

®

 Keyless 

Entry System. If you purchase a new remote, or if you 
wish to deactivate any remote, follow the instructions in 
the 

Programming 

section. 

Activate your opener with any of the following:

• 

 

The hand-held Remote Control:

 Hold the large push 

button down until the door starts to move.

• 

 

The wall-mounted Door Control:

 Hold the push button 

or bar down until the door starts to move.

• 

 

The Keyless Entry (See Accessories):

 If provided with 

your garage door opener, it must be programmed 
before use. See 

Programming

.

When the opener is activated (with the safety reversing 
sensor correctly installed and aligned)

1.   If open, the door will close. If closed, it will open.

2.   If closing, the door will reverse.

3.   If opening, the door will stop.

4.   If the door has been stopped in a partially open 

position, it will close.

5.   If obstructed while closing, the door will reverse. If the 

obstruction interrupts the sensor beam, the opener 
lights will blink for fi ve seconds.

6.   If obstructed while opening, the door will stop.

7.   If fully open, the door will not close when the beam is 

broken. The sensor has no effect in the opening cycle.

If the sensor is not installed, or is misaligned, the door 
won't close from a hand-held remote. However, you can 
close the door with the Door Control, the Outdoor Key 
Switch, or Keyless Entry, 

if you activate them until down 

travel is complete.

 

If you release them too soon, the door 

will reverse. 

The opener lights

 will turn on under the following 

conditions: when the opener is initially plugged in; when 
power is restored after interruption; when the opener is 
activated. 

They will turn off automatically after 4-1/2 minutes or 
provide constant light when the Light feature on the
Multi-Function Door Control Panel is activated. Bulb size is 
A19. Bulb power is 100 watts maximum.

Security

®

 light feature:

 

Lights will also turn on when 

someone walks through the open garage door. With a 
Multi-Function Door Control Panel, this feature may be 
turned off as follows: With the opener lights off, press and 
hold the light button for 10 seconds, until the light goes 
on, then off again. To restore this feature, start with the 
opener lights on, then press and hold the light button for 
10 seconds until the light goes off, then on again.

Summary of Contents for PD432DM 1/2 HP Owners









































Reviews: