background image

35

KG

1

3

9

7

5

KG

1

3

9

7

5

LOCK

LIGHT

*3-Button Remotes (315 MHz)

If provided with your garage door opener, the 
large button is factory 
programmed to operate it. 
Additional buttons on any
Security

®

 3-Button remote 

or mini-remote can be 
programmed to operate 
other Security

®

 

garage door openers.

To Erase All Codes From Motor

Unit Memory

To deactivate any unwanted remote, fi rst erase all 
codes:
Press and hold the “learn” 
button on motor unit until the 
learn indicator light goes out 
(approximately 6 seconds). All 
previous codes are now erased. 
Reprogram each remote or keyless 
entry you wish to use.

1.   Press and hold the button 

on the hand-held remote* 
that you wish to operate your 
garage door.

2.   While holding the remote 

button, press and hold the 
LIGHT button on the 
Multi-Function Door Control.

3.   Continue holding both buttons 

while you press the push bar 
on the Multi-Function Door 
Control (all three buttons are 
held).

4.   Release buttons when the 

motor unit lights blink. It has 
learned the code. If light bulbs 
are not installed, two clicks will 
be heard.

1.   Press and release the “learn” 

button on the motor unit. The 
learn indicator light will glow 
steadily for 30 seconds.

2.   Within 30 seconds, press and 

hold the button on the hand-
held remote

*

 that you wish to 

operate your garage door.

3.   Release the button when the 

motor unit lights blink. It 
has learned the code. If light 
bulbs are not installed, two 
clicks will be heard.

To Add or Reprogram a Hand-held Remote Control

USING THE “LEARN” BUTTON 

USING THE MULTI-FUNCTION DOOR CONTROL

LOCK

LIGHT

LOCK

LIGHT

PROGRAMMING

Your garage door opener has already been programmed at the factory to operate with your hand-held remote control. 
The door will open and close when you press the large push button.

Below are instructions for programming your opener to operate with additional Security

®

 remote controls.

NOTICE: 

If this Security

®

 garage door opener is operated with a non-rolling code transmitter, the technical measure 

in the receiver of the garage door opener, which provides security against code-theft devices, will be circumvented. The 
owner of the copyright in the garage door opener does not authorize the purchaser or supplier of the non-rolling code 
transmitter to circumvent that technical measure.

Summary of Contents for PD432DM 1/2 HP Owners









































Reviews: