background image

17

OPERATION

IMPORTANT SAFETY INSTRUCTIONS

To reduce the risk of SEVERE INJURY or DEATH:

WARNING

WARNING

1. READ AND FOLLOW ALL WARNINGS AND

INSTRUCTIONS.

2. ALWAYS keep transmitters out of reach of children.

NEVER permit children to operate or play with the

wireless wall button, multi-fucntion door control or

transmitters.

3. ONLY activate the door when it can be seen clearly,

it is properly adjusted and there are no obstructions

to door travel.

4. ALWAYS keep the door in sight until completely

closed. NO ONE SHOULD CROSS THE PATH OF THE

MOVING DOOR.

5. NO ONE SHOULD GO UNDER A STOPPED,

PARTIALLY OPENED DOOR.

6. If possible, use emergency release handle to

disengage door ONLY when the door is CLOSED.

Weak or broken springs or unbalanced door could

result in an open door falling rapidly and/or

unexpectedly.

7. NEVER use emergency release handle unless the

doorway is clear of persons and obstructions.

8. After ANY adjustments are made, the safety

reversal system MUST be tested.

9. Safety reversal system MUST be tested every

month. The door MUST reverse on contact with

40mm (1 1/2”) high obstacle on the floor.

10. ALWAYS KEEP THE DOOR PROPERLY BALANCED

(see page 3). An improperly balanced door may

not reverse when required and could result in

SEVERE INJURY or DEATH.

11. ALL repairs to cables, spring assemblies and other

hardware, ALL of which are under EXTREME

tension, MUST be made by a trained door systems

technician.

12. ALWAYS disconnect electric power to the door

opener BEFORE making ANY repairs or removing

covers.

13. Permanently fix the Emergency release instruction

Label adjacent to the release handle.

14.

SAVE THESE INSTRUCTIONS.

EMERGENCY DOOR RELEASE

ADJUSTMENT STEP 7

To Open the Door Manually

Disengage door lock before proceeding. The door should be fully

closed if possible. Pull down on the emergency release handle

until a click noise is heard from the unit and lift the door

manually. To reconnect the door to the opener, pull down the

emergency release handle straight down a second time until a

click noise is heard from the unit. The door will reconnect on the

next UP or DOWN operation.

Test the emergency release:

• Make sure the door is closed.
• Pull the emergency release handle. The door should then be

able to be opened manually.

• Return the door to the closed position.
• Pull the emergency handle a second time.
• Reconnect the door to the opener.

NOTICE

Emergency
Release Handle

WARNING

To prevent possible SERIOUS INJURY or DEATH from a falling door:

• If possible, use emergency release handle to disengage door ONLY when door is CLOSED. Weak or

broken springs or unbalanced door could result in an open door falling rapidly and/or unexpectedly.

• NEVER use emergency release handle unless the doorway is clear of persons and obstructions.

Powered Door Lock

Manual Releas

Lock Bolt
“Locked”

Summary of Contents for Merlin MJ3800

























Reviews: