background image

35

*3-Button Remotes

If provided with your garage
door opener, the large button
is factory programmed to
operate it. Additional buttons
on any Security

®

3-Button

remote or compact remote
can be programmed to
operate other Security

®

garage door openers.

To Erase All Codes From Motor Unit

Memory

To deactivate any unwanted remote, first erase all codes:

Press and hold the “learn” button on
motor unit until the learn indicator light
goes out (approximately 6 seconds). All
previous codes are now erased.
Reprogram each remote or keyless entry
you wish to use.

1. Press and release the “learn” button

on the motor unit. The learn indicator
light will glow steadily for 30 seconds.

2. Within 30 seconds, press and hold the

button on the hand-held remote

*

that

you wish to operate your garage door.

3. Release the button when the motor

unit lights blink. It has learned the
code. If light bulbs are not installed,
two clicks will be heard.

To Add or Reprogram a Hand-held Remote Control

USING THE “LEARN” BUTTON

USING THE MULTI-FUNCTION DOOR CONTROL

PROGRAMMING

Your garage door opener has already been programmed at the factory to operate with your hand-held remote control.
The door will open and close when you press the large push button.

Below are instructions for programming your opener to operate with additional Security

®

remote controls.

1. Press and hold the button on the

hand-held remote

*

that you wish to

operate your garage door.

2. While holding the remote button,

press and hold the LIGHT button on
the Multi-Function Door Control.

3. Continue holding both buttons while

you press the push bar on the Multi-
Function Door Control (all three
buttons are held).

4. Release buttons when the motor unit

lights blink. It has learned the code. If
light bulbs are not installed, two clicks
will be heard.

LOCK

LIGHT

LOCK

LIGHT

NOTICE:

If this Security

®

garage door opener is operated with a non-rolling code transmitter, the technical measure in

the receiver of the garage door opener, which provides security against code-theft devices, will be circumvented. The
owner of the copyright in the garage door opener does not authorize the purchaser or supplier of the non-rolling code
transmitter to circumvent that technical measure.

KG

1

3

9

7

5

KG

1

3

9

7

5

LOCK

LIGHT

Summary of Contents for 995XD









































Reviews: