background image

30

OPERATION 

Using Your Garage Door Opener

Your Security

®

opener and hand-held remote control

have been factory-set to a matching code which changes
with each use, randomly accessing over 100 billion new
codes. Your opener will operate with up to eight
Security

®

remote controls and one Security

®

Keyless

Entry System. If you purchase a new remote, or if you
wish to deactivate any remote, follow the instructions in
the 

Programming

section. 

Activate your opener with any of the following:

The hand-held Remote Control:

Hold the large push

button down until the door starts to move.

The wall-mounted Door Control:

Hold the push button

or bar down until the door starts to move.

The Keyless Entry (See Accessories):

If provided with

your garage door opener, it must be programmed
before use. See 

Programming.

When the opener is activated (with the safety
reversing sensor correctly installed and aligned)

1. If open, the door will close. If closed, it will open.
2. If closing, the door will reverse.
3. If opening, the door will stop.

4. If the door has been stopped in a partially open

position, it will close.

5. If obstructed while closing, the door will reverse. If the

obstruction interrupts the sensor beam, the opener
lights will blink for five seconds.

6. If obstructed while opening, the door will stop.
7. If fully open, the door will not close when the beam is

broken. The sensor has no effect in the opening cycle.

If the sensor is not installed, or is misaligned, the door
won

'

t close from a hand-held remote. However, you can

close the door with the Door Control, the Outdoor Key
Switch, or Keyless Entry, 

if you activate them until down

travel is complete. 

If you release them too soon, the door

will reverse. 

The opener lights

will turn on under the following

conditions: when the opener is initially plugged in; when
power is restored after interruption; when the opener is
activated. 

They will turn off automatically after 4-1/2 minutes or
provide constant light when the Light feature on the
Multi-Function Door Control Panel is activated. Bulb size
is A19. Bulb power is 100 watts maximum.

Security

®

light feature: 

Lights will also turn on when

someone walks through the open garage door. With a
Multi-Function Door Control Panel, this feature may be
turned off as follows: With the opener lights off, press
and hold the light button for 10 seconds, until the light
goes on, then off again. To restore this feature, start with
the opener lights on, then press and hold the light button
for 10 seconds until the light goes off, then on again.

IMPORTANT SAFETY INSTRUCTIONS

To reduce the risk of SEVERE INJURY or DEATH:

WARNING

WARNING

WARNING

1. READ AND FOLLOW ALL WARNINGS AND INSTRUCTIONS.
2. ALWAYS keep remote controls out of reach of children.

NEVER permit children to operate or play with garage door
control push buttons or remote controls. 

3. ONLY activate garage door when it can be seen clearly, it is

properly adjusted, and there are no obstructions to door
travel.

4. ALWAYS keep garage door in sight until completely closed.

NO ONE SHOULD CROSS THE PATH OF THE MOVING
DOOR.

5. NO ONE SHOULD GO UNDER A STOPPED, PARTIALLY

OPENED DOOR.

6. If possible, use emergency release handle to disengage

trolley ONLY when garage door is CLOSED. Weak or broken
springs or unbalanced door could result in an open door
falling rapidly and/or unexpectedly.

7. NEVER use emergency release handle unless garage

doorway is clear of persons and obstructions.

8. NEVER use handle to pull garage door open or closed. If

rope knot becomes untied, you could fall.

9. If one control (force or travel limits) is adjusted, the other

control may also need adjustment.

10. After ANY adjustments are made, the safety reversal

system MUST be tested.

11. Safety reversal system MUST be tested every month.

Garage door MUST reverse on contact with 1-1/2" high 
(3.8 cm) object (or a 2x4 laid flat) on the floor.

12. ALWAYS KEEP GARAGE DOOR PROPERLY BALANCED

(see page 3). An improperly balanced door may not
reverse when required and could result in SEVERE INJURY
or DEATH.

13. ALL repairs to cables, spring assemblies and other

hardware, ALL of which are under EXTREME tension,
MUST be made by a trained door systems technician.

14. ALWAYS disconnect electric power to garage door opener

BEFORE making ANY repairs or removing covers.

15.

SAVE THESE INSTRUCTIONS.

Summary of Contents for 995XD









































Reviews: