Chamberlain 3595LM 3/4 HP, Owner'S Manual

Page: 25 / 36

Troubleshooting
Reduced proximity
sensing (does not
activate by
touching top of
remote control)
Check if proximity lighting is
disabled by pressing a button.
Replace 3 V 2450 battery with
same type 3 V 2450 coin cell.
The Proximity Sensor may be
oversensitized. Sit remote control
undisturbed for 60 seconds on a
non-metallic surface. This allows
the sensor to recalibrate itself.
Dim LED lights
Replace two 3 V 2016 batteries
with same type 3 V 2016 coin
cells.
No rapid LED
blinking after
pressing a button
Replace two 3 V 2016 batteries
with same type 3 V 2016 coin
cells.
SOLUTION
Using the Remote Control
NOTE: To activate the remote control functions, pull out
the plastic pull tab protruding from the remote control
housing.
This remote control is equipped with a proximity lighting
feature. When moving a hand within close proximity to the
remote control, the LED lights turn on for 3 seconds. Upon
successful activation of a remote control button, the LED
lights will blink rapidly.
Proximity Disable Feature
The remote control will turn off the proximity lighting
feature if the proximity lighting is turned on 10 consecutive
times without activation of a button. To re-enable the
proximity lighting, simply press a button. This function
conserves battery life.
To Control the Opener Lights
With 315MHz Security
✚
® remote controls, a remote push
button can be programmed to operate the opener lights
without opening the door.
1. With the door closed, press and hold the remote button
that you want to control the light.
2. Press and hold the Light button on the multi-function
control panel.
3. Press and hold the Lock button on the multi-function
control panel.
4. After the opener lights flash, release all buttons.
Test by pressing the remote push button. The opener
lights should turn on or off but the door should not move.
Open/Close/Stop Operation
Your 315MHz Security
✚
®
remote control can be
programmed to operate one door using all 3 buttons: the
button with one light slot will only open the door, the
button with two light slots will close the door, and the
button with three light slots will stop the door’s movement.
You may set up this feature as follows:
1. With the door closed, press
and hold the button with
one light slot.
2. Press and hold the Lock
button on the multi-function
control panel.
3. Press and hold the main door control push button.
When the opener lights flash, release all buttons. Test by
pressing the 1 light slot button (Open) on the remote. The
door should open. Press it again while the door is open
and nothing should happen. Press the 2 light slot button
(Close) while the door is moving and it should close. Press
the 3 light slot button (Stop) and the door should stop
immediately.
1 Light Slot
(Open)
2 Light Slots
(Close)
3 Light Slots
(Stop)
The Remote Control Battery
The 3 V 2016 lithium
batteries for the opener and
LED lights (marked “LED
and Opener Battery”) should
last 5 years. The 3
V 2450
lithium battery for the
proximity lighting (marked
“Proximity Battery”) should
last 1-2 years. To replace
the batteries, remove the
two screws and open the
remote control housing.
Push the battery out of the holder for removal. Insert
replacement batteries positive side up. Dispose of old
batteries properly.
Replace the batteries with only 3 V 2016 or 3 V 2450 coin
cell batteries. Use of another cell may present a risk of fire
or explosion.
CAUTION: Do not bend spring contact. If bent the
proximity sensor will not work.
To prevent possible SERIOUS INJURY or DEATH:
• NEVER allow small children near batteries.
• If battery is swallowed, immediately notify doctor.
WARNING
CAUTION
WARNING
WARNING
Proximity
Battery