background image

Model 15000-3S & 15000-SPRINTER 

Installation, Operation and Maintenance 

 Page 

9  

Rev. 8/13/19

 

 

 

15-3S-IOM-A.doc 

L

OCK 

R

ELEASE

 

30) Assemble the fittings to the air valve, 

Fig. 15

with the barbed fitting (3/8” hose barb x 1/8NPT) 
in port marked “1”, the elbow (1/8” push-lock x 
1/8NPT) in port “2”, and nothing in the center 
port “3” (exhaust).  

31) Assemble the palm button to the valve.  Cut a 

piece of the 1/8” O.D. air line 1 1/2" long and use 
it to connect the center of the Tee fitting to the 
elbow. 

 

Fig. 15 – Cable Assembly 

32) On the Power Column, attach the 1/8” air line 

from the lock release air cylinder to the bottom of 
the push-lock tee fitting,

 Fig 16

33) Connect the rest of the 1/8” air line to the top of 

the tee and run it along side the hydraulic hose 
up the column and across the overhead 
attaching it to the hydraulic hose with wire ties 
(

Fig 16

). 

34) At the Idler side feed the air line thru the opening 

in the column extension and down the column 
using adhesive tabs and wire ties.  Attach it to 
the lock release air cylinder (

Fig. 16

). 

 

Fig. 16 – Lock Release

 

35) Remove the two nuts securing the right side of 

the power unit, install the valve cover with these 
nuts, and secure the hose to the cover with wire 
ties, 

Fig. 17

 

Fig. 17 – Cable Assembly 

Summary of Contents for 15000-SPRINTER 15000-3S























Reviews: