3
NORSE Operating Manual & Parts List 9681310 & 9681311
GETTING STARTED
Save this manual
You will need this manual for the safety warnings and
precautions, assembly instructions, operating and maintenance
procedures, parts list and diagram. Keep your invoice with this
manual. Write the invoice number on the inside of the front cover.
Keep this manual and invoice in a safe and dry place for future
reference.
Structural requirements
Make sure all supporting structures and load attaching
devices are strong enough to hold your intended loads.
If in doubt, consult a qualified structural engineer.
Electrical requirements
The power supply to your specific Disc Sander is
determined by its model number. Model 9681310
requires 115V, 60Hz, 17.8 amps. Model 9681311
requires 230V, 60Hz, 11.2 amps single phase. The
standard allowable voltage variation is a plus or minus 10%.
UNPACKING
When unpacking, check to make sure all parts listed below are
included. If any parts are missing or broken, please contact your
local retailer.
Never use highly volatile solvents. Avoid
getting cleaning solution on paint as it
may tend to deteriorate these finishes. Use soap and water
on painted components.
IMPORTANT:
Many unpainted steel surfaces will have been
coated with a protectant. To ensure proper fit and operation,
remove the coating. Coating can be easily removed with mild
solvents, such as mineral spirits and a soft cloth. Avoid getting
solution on paint or any of the rubber/plastic parts. Solvents may
deteriorate these finishes. Use soap and water on paint, plastic
or rubber components. After cleaning, cover all exposed surfaces
with a light coating of oil.
Contents:
• Disc Sander
• 5 mm Hex Wrench
• Miter Guage
• Adhesive Backed Sanding Disc
• Anti-vibration Foot Pads
Unpack
Remove all the over packing materials, but leave unit
attached to its pallet. Do not discard packing materials
until after the machine has been inspected for damage and
completeness. Locate loose parts and set them aside.
Inspect
• After unpacking the unit, carefully inspect for any
damage that may have occurred during transit.
Check for loose, missing or damaged parts.
Shipping damage claims must be filed with the
carrier.
• All tools should be visually inspected before use, in addition
to regular periodic maintenance inspections.
• Be sure that the voltage labeled on the unit matches your
power supply.
SAFETY RULES
For your own safety, read all of the
instructions and precautions before
operating tool.
Always follow proper operating
procedures as defined in this manual even
if you are familiar with the use of this tool or similar
machines. Remember that being careless for even a fraction
of a second can result in severe personal injury.
PROPOSITION 65 WARNING:
Some dust created by
using power tools contain chemicals known to the state
of California to cause cancer, birth defects or other
reproductive harm.
Some examples of these chemicals are:
• Lead from lead-based paints.
• Crystalline silica from bricks and cement and other masonry
products
• Arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on how often
you do this type of work. To reduce your exposure to these
chemicals: work in a well ventilated area and work with approved
safety equipment. Always wear a
OSHA/NIOSH
approved,
properly fitting face mask or respirator when using such tools.
Preparing for your job
• Wear safety glasses complying with United States ANSI
Z87.1. Everyday glasses only have impact resistant lenses.
They are not safety glasses.
• Wear an ANSI approved dust mask.
• Wear proper apparel when using this tool. Do not wear loose
clothing, gloves, neckties, rings, bracelets or other jewelry
which may get caught up in moving parts of this machine.
• When using this machine, wear protective hair covering to
contain long hair.
• Wear safety shoes with non-slip soles.
• Be alert and think clearly. Never operate power tools when
tired, intoxicated or when taking medications that cause
drowsiness.
Preparing the work area for your job
• Keep your work area clean. Cluttered work areas invite
accidents.
• Do not set up or use the Disc Sander in dangerous
environments. Do not set up or use the Disc Sander in damp
or wet locations. Do not expose this machine to rain.
• Make sure your work area is properly lighted.
• Proper electrical connections should be set up for this
machine.
• Extension cords should have a grounding prong and the
