background image

     3300IP VoIP Phone | User Manual 

www.CetisGroup.com 

17 

 

Reference – Quick Keys 

The TeleMatrix family of SIP phones has 
implemented an innovative way to determine 
various states of the SIP phone and the 
network it is attached to via the phone’s dial-
pad. By pressing the * key twice in 
succession followed by a series of numbers 
(generally matched to the command’s 
corresponding letters.) 
 

 
 

Many of these features are newly added in Firmware 1.8.0 and higher. 

 
Show IP address - **47#  (**IP#)

 

Description: Keying **47# causes the phone to read out the IP address currently assigned. If the phone has an 
LCD panel, it should be displayed there. If the phone has no display panel, or the address cannot be displayed, 
it should be read out audibly on the speaker (or handset if off hook.) 
 

Show VLAN - **85# (**VL#) 

Description: When entered respond with the Voice VLAN ID. If VLAN is disabled “Zero” to indicate “off” is 
spoken. 
 

Set VLAN - **87# (**87*password*VLANid#) 

Description: This allows the user to set the VLAN ID. The keypad password is also required. To set the VLAN 
ID when the password is 9382 and the VLAN ID is 30, enter "**87*123*301#". When a VLAN ID is set, the 
phone should set VLAN Enabled and the Voice VLAN ID. If necessary the LAN should be set to Bridge mode 
also. 
 

Show Firmware Version - **39# (**FW#)

 

Description: When **39# is entered, the phone will display or audibly respond with the firmware version number 
such as "1.7.240.235". 
 

Show TFTP Server Address - **83# (**TF#)

 

Description: When entered, the phone responds with the IP address of the TFTP 
server. This should be the TFTP server address being actually used. It might come from the configuration file, 
option 66, option 125 or option 43. 
 

Re-program New ConfigID - **77*password*ConfigID# (**RP*xxx*yyyy#)

 

Description: After entering **77*, the user must enter the Keypad Password followed by a * then the ConfigID of 
the new config file, followed by #. If the password (in the existing config on the phone is 123, and the new 
config file is 1234.3300ip.txt), then the user would enter **77*123*1234#. The user should NOT be prompted 
for the password. The phone will then download the new config file 1234.3300ip.txt. 
 

Reset phone to Factory Default – **33*<password># = (**DE*123#)

 

Description: After entering **33*123#, the phone will reset to factory default, which implies that there is no 
programming information current, and the phone will prompt for a ConfigID at reboot. 
 

Re-boot phone (without reset) – **72# (**RB#)

 

Description: After entering 72#, the phone will reboot 

 

SIP TeleWorker Config File Download – **89*<tftp server IP address>*<ConfigID># 

 

Description: To download a config file for a phone remotely, this **TW code is used for designating a tftp server 
IP address and configID to download.  

Summary of Contents for 3300IP






















Reviews: