CertainTeed Bufftech Assembly & Installation Manuallines Download Page 6

Page: 6 / 60

Tools and Materials

Getting Started

•   Site plans and permits
•   Measuring  tape
•   Hammer or mallet
•   Wooden  stakes
•   String  line
•   Spray paint for hole centers for post and

gate spacing

• Wooden spacer bar for post and gate spacing
• Level
• Concrete

Assembling Fence/Gates

• Drop cloth
• Hacksaw, circular saw or chop saw with

masonry blade

•   Square
•   #3 square drive bit
•   Phillips #2 screwdriver
•   Drill and drill bits
- 1/8" for #8 screws
-  1/4" for bullet clips

and drain holes

- 11/64" for gate assembly
- 5/32" for gate hardware if using

aluminum insert

- 3/8" for lock rings
• 1/2" deep socket (or nut driver)

for traditional picket

• 3/8" nut-driver - Molded

Digging Holes

•   Post hole digging tools
- Shovel
- Post hole digger
-  10" auger for 4x4 posts
-  12" auger for 5x5 posts

Installing Post

•   Wheelbarrow
•   Concrete mixing tools
•   Short length of wood,

2x4 for tamping concrete

• Garden hose
• Level

Installing Bottom Rail

•   Leveling  blocks
•   Shim  stock
•   Duct tape to seal rail ends

Installing Gate(s) Extruded

• Wrench
- 7/16" for hinge nuts
• Flat screwdriver to activate hinge spring

Installing Gate(s) Molded

• 7/32"Allen wrench
• 3/8" nut-driver

Filling Post with Concrete
extruded

•   Rubber mallet to tamp post
•   Funnel for filling post
•   Ladder for high fences

Cleaning Up

• Abrasive-type pad
• Bucket and sponge

Additional Tools -
Installing on Concrete

• 1/2" masonry drill
• Core drill

Additional Tools -
EZ Set Brackets

•   7/16"  wrench
•   Post routing - Extruded
•   Template kit with router
•   Spiral  saw

Summary of Contents for Bufftech





























































Search results

Summary of Contents for Bufftech

Reviews:

Related manuals for Bufftech

Brands by name

Popular brands

CertainTeed Bufftech, Assembly & Installation Manuallines

Search results

Summary of Contents for Bufftech

Reviews:

Related manuals for Bufftech

Brands by name

Popular brands