CertainTeed Bufftech Assembly & Installation Manuallines Download Page 54

Page: 54 / 60

Concrete Installation –

Molded

Concrete Install - Molded

Molded fence panels can be installed on top of a 10" minimum

width poured concrete wall or on flat concrete using our

concrete mounting brackets. Concrete mounts are available for

end, gate, line, and corner posts along with post skirts for a

clean look. Be sure concrete is structurally sound for

installation of fence.

1. Cutting down post

a. Measure height from top of post

b. Cut off bottom of post with metal cutting blade

c. Never cut the top of the post

2. Install concrete mounting brackets

a. Drill all four holes through the pre-drilled holes in

the steel plate

b. Install concrete mounts to concrete with fasteners

with at least 4,000 lbs. shear strength (minimum

bolt size is 1/2" x 4-1/2")

c. Shim to level if necessary

3. Install post skirts

4. - install post to concrete mounting bracket

a. attached to concrete mounting bracket with three

screws

(line post - insert three stagged screws on each side

of the strap into the pre-drilled holes)

5. - install fence panels and post caps

NOTE: Because panels normally sit directly on the wall or

concrete surface panel brackets are unnecessary when using

concrete mounts.

Summary of Contents for Bufftech





























































Search results

Summary of Contents for Bufftech

Reviews:

Related manuals for Bufftech

Brands by name

Popular brands

CertainTeed Bufftech, Assembly & Installation Manuallines

Search results

Summary of Contents for Bufftech

Reviews:

Related manuals for Bufftech

Brands by name

Popular brands