Cermetek Microelectronics, Inc.
High Speed Internet Modem Family
2005 Cermetek Microelectronics, Inc.
Page 7
Document No. 607-0017 Revision I1 (05/05)
Table 1. Summary of CH2124/60 Allowed @T
®
Commands (Continued).
Command Notes
Description
@T
[
K10
][
=n
]
1,2,6,9
Select DTE Baud rate:
n=01
Select DTE baud rate
115200
.
n=02
Select DTE baud rate
57600
. (Default CH2160)
n=11
Select DTE baud rate
38400
.
n=12
Disabled.
n=13
Select DTE baud rate
9600
.
n=14
Select DTE baud rate
4800
.
n=15
Select DTE baud rate
2400
. (Default CH2124)
n=16
Disabled.
@T
[
K11
][
=n
]
1,2,6,9,
14
Enable/Disable Remote Dial-up Access. For
n
greater than 00, Remote Dial-up Access is
enabled and
n
specifies the number of rings required before iModem will answer the
incoming call. Specified in HEX.
n=00
Disable Remote Dial-up Access.
n=02
Enable Remote Dial-up Access to answer after 2 ring (minimum allowed) (Default)
n=FF
Enable Remote Dial-up Access to answer after 255 rings (maximum allowed).
@T
[
LM
][
=n
]
1,2
Enter POP3 Login name,
n
.
@T
[
L1
][
=n
]
1,2
Enter ISP Login name,
n
.
@T
[
M1
][=
n
]
1,2
Enter user defined email message,
n
. End with
<CR><LF>.<CR><LF>
. The mail message
must be entered after all other ISP parameters have been set. Additionally, any carriage
return
<CR> (HEX ØD)
included in the message is interpreted as a carriage return
<CR>
line
feed
<LF>
(HEX ØD ØA)
. This is for compatibility with commercial terminal emulation
programs. The message length is currently limited to 125 ASCII characters. Blanks or
spaces are allowed and count as 1 character per each occurrence. The entered message is
stored in message memory location
M1
.
@T
[
N1
][
=n
]
1,2
Enter local access phone number for ISP,
n
.
@T
[
OP1
][
=n
]
1,2
Enter POP3 server IP HEXIDECIMAL address,
n
.
@T
[
OS1
][
=n
]
1,2
Enter SMTP server IP HEXIDECIMAL address,
n
.
@T
[
PW
][
=n
]
1,2
Enter Dialup Password. Maximum length is 15 alphanumeric ASCII characters.
@T
[
PM
][
=n
]
1,2
Enter POP3 Password. Maximum length is 16 alphanumeric ASCII characters.
@T
[
P1
][
=n
]
1,2
Enter password for ISP, n. Blanks or spaces are not allowed.
@T
[
Q
][
=n
]
1,2,3,4
Terminate iModem mode of remotely accessed iModem during Remote Dial-up Access
session. Switch to standard analog modem mode while maintaining current Remote Dial-up
Access session.
@T
[
S1
][
=n
]
1,2,3,4
Enter email subject line, n. The subject line length is currently limited to 16 ASCII characters.
Blanks or spaces are allowed and count as 1 character per each occurrence. The same
subject line is used for both the
Input Port Status
message and the
User Defined
message.
@T
[
U1
][
=n
]
1,2
Enter iModem Device Name. No special characters allowed (i.e., %, *). Maximum length is 16
alpha-numeric ASCII characters.
@T
[
Z
][]
1,2,11
Restores factory set profile (i.e., phone number, username, password, SMTP mail server
address, iModem local email address subject and message body).
@T
[
Z
][
n
]
1,2,11
Set current ACTIVE ISP profile (i.e., phone number, username, password, SMTP mail server
address, iModem local email address subject and message body) from factory set profiles.
n=0
Restore factory set ISP profile. Same as
@TZ
.
