background image

 

 

Revision 3.0  September 2019 
© 2019 Centrica plc. Registered office: Millstream, Maidenhead Road, Windsor, Berkshire. SL4 5GD.  
Registered in England & Wales No 3033654 
 

PAN-14 Sensor installation guide 

Copyright notice 

Copyright

©

 2014-2019 Panoramic Power Ltd. All rights reserved. 

Panoramic Power® is a registered trademark of Panoramic Power Ltd.  
All other trademarks are the property of their respective owners. 

FCC compliance statement 

This device has been tested and found to comply with the limits for a Class B 
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed  
to provide reasonable protection against harmful interference in residential 
installations. This equipment generates uses and can radiate radio frequency 
energy and, if not installed and used in accordance with the instructions, may 
cause harmful interference to radio and television reception. 

However, there is no guarantee that interference will not occur in a particular 
installation. If this device does cause such interference, which can be verified by 
turning the device off and on, the user is encouraged to eliminate the 
interference by one or more of the following measures: 

 

Re-orient or re-locate the receiving antenna. 

 

Increase the distance between the device and the receiver. 

 

Connect the device to an outlet on a circuit different from the one that  
supplies power to the receiver. 

 

Consult the dealer or an experienced radio/TV technician. 

Warning

 Changes or modifications to this unit not expressly approved by the 

party responsible for compliance could void 

the user’s authority to operate the 

equipment. 

This device complies with Part 15 of the FCC Rules. Operation is subject to  
two conditions: 

1.

 

This device may not cause harmful interference, and 

2.

 

This device must accept any interference that may be received or that  
may cause undesired operation. 

Manufacturer i

nformati

on 

Panoramic Power Ltd.  
15  Atir Yeda St.,  
Kfar Saba 4464312, Israel 

Telephone: +972-9-7667600 

 

 
 

 

Summary of Contents for PAN-14












Reviews: