background image

Page 10

SKU 97053

For technical questions, please call 1-800-444-3353.

To adjust the water flow rate of the Sander, turn the Water Flow Control located 

5. 

on the Anchor Assembly (43).  

(See Figure D.)

Sand the workpiece evenly with gentle, broad, sweeping strokes in a criss-cross 

6. 

pattern.
During the sanding process, it may become necessary to occasionally stop the 

7. 

Sander, disconnect the tool from its compressed air supply source, remove any 

remaining compressed air from the tool by squeezing its Valve Lever (1), and 

replace the worn Sand Paper Disc with a new Disc.  

(See Figure E.)

Once the sanding is completed, release pressure on the Valve Lever (1) to stop 

8. 

the Sander.  Remove the Anchor Assembly (43) from its container of water.  

Restart the Sander to empty the tool of any remaining water.  Turn off the air 

compressor.  Disconnect the Sander from its air supply hose.  Then squeeze the 

Valve Lever once again to release any remaining compressed air from the tool.  

(See Figures D and E.)

Make sure to store the Sander in a clean, dry, safe location out of reach of 

9. 

children and other unauthorized people.

MAINTENANCE AND SERVICINg

Risk of serious personal injury from accidental starting.  

Disconnect the Sander from its compressed air supply 

before performing any inspection, maintenance, or cleaning 

procedures.
Damaged equipment can fail, causing serious personal 

injury.  Do not use damaged equipment.  If abnormal noise or 

vibration occurs, have the problem corrected before further 

use.

BEFORE EACH uSE,

1. 

 inspect the general condition of the Sander.  Check for 

loose parts, misalignment or binding of moving parts, cracked or broken parts, 

damaged hose, and any other condition that may affect its safe operation.

DAILY,

2. 

 top off the Sander’s Oil Port with pneumatic tool oil.  To do so, disconnect 

the tool from its compressed air supply source and release all remaining air 

pressure from the tool by pressing the Valve Lever (1).  Use the provided Allen 

Wrench (49) to unscrew and remove the Allen Screw (46) located at the top of 

the tool.  Then replace the Allen Screw. 

(See Figure E.)
DAILY, 

3. 

check the Strainer (44) in the Anchor Assembly (43) for excess dirt and 

debris.  If necessary, clean Strainer.  

(See Assy. Diagram.)

WARNINg

Summary of Contents for Professional 97053















Reviews: