background image

Page 16

For technical questions, please call 1‑800‑444‑3353.

SKU 68024 

        

PLEASE READ THE FOLLOWING CAREFULLY

THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY 

DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY.  NEITHER THE MANUFACTURER OR 

DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE 

OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED 

TO REPLACE ANY PARTS OF THE PRODUCT.  IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR 

EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY 

CERTIFIED AND LICENSED TECHNICIANS, AND NOT BY THE BUYER.  THE BUYER ASSUMES ALL RISK 

AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT 

PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.

2.  Remove the jammed fasteners 

with pliers.

3.  If a fastener is jammed in the Magazine, 

lift open the Latch, and then swing back 

the moveable Cover Plate and then the 

Magazine Cover. 

4.  Uncoil the fasteners and, if necessary, 

use a screwdriver to release the 

jammed fastener. 

5.  Pull out the jammed fastener. 
6.  If you are unable to clear the fastener 

jam using the method prescribed above, 

the tool should be taken to a qualified 

service technician for proper servicing.

Record Product’s Serial Number Here: 
Note:

  If product has no serial number, record month and year of purchase instead.

Note:

  Some parts are listed and shown for illustration purposes only, and are not available 

individually as replacement parts.

Summary of Contents for 68024





















Reviews: